Aukru Aluminum Raspberry Pi Heatsink, Silver Pack of 4 (3+1)

All 3 heatsinks look great and well done. Cleaned the chips prior installation, and all got attached very well. Temperature dropped from 60 to 47 straight away at idle, and from 65 to 52 when watching movies. Fits great on the rpi3 model b black case, the standard one.

Ordered these for the VRAM my 1080Ti, they work great. For some reason, however, the adhesive does not like to stick to the VRAM modules, it’s almost like there is an oily layer on them. I ended up using some of my own thermally conductive tape, which wasn’t much better. I think it’s an issue with the GPU rather than the preapplied tape.

These heatsinks are very good quality. I've just bought a Pi3 and new case with a small fan. The two heatsinks for the top of the board are a perfect fit and size, the heatsink for the chip underneath hit the metal casing so I decide not to use it as it would have bent the board slightly. The two top heatsinks + fan do keep inside the case cool as I drive it quite hard with the application I am running.

These heatsinks were ideal for my Raspberry Pi 3 and lowered the temperature well. They are self adhesive and can be attached quickly and easily. The only point to watch is whether there's enough space to fit them if you've got your Pi in a case.

I ordered two sets of these 1 was absolutely perfect the other one was appalling the adhesive strips was not on the bottom of the heatsinks properly so it had stuck to the bag making black sticky marks all over the heatsinks also making it very unlikely to stick to the chips

Cheap, good quality heat sink for the Pi 3. Comes pre-applied with self-adhesive pads for easy fitting. Arrived very quickly and well packaged. No height issues fitting these with the official Pi case.

I was a bit skeptical about these heatsinks but they do make a difference. I was getting a high temp warning on the Pi while it was indexing my media files so I put them on and they did drop the temperature enough. The only problem was I wasn't sure about the placement of the heatsinks so a small manual would have been nice. By the way the copper heatsink goes on the chip underside of the board.

These little heatsinks are enough to wick away some heat, but ultimately if you're doing long intensive processes it will end up being the same temperature as without. You will need a little fan if this is the case.

Comprati per venir utilizzati su un Raspberry 3 A+ che raggiungeva temperature leggermente troppo alte. Il prodotto si applica facilmente grazie alla ottima pasta termina pre-applicata e funziona egregiamente: le temperature si sono abbassate di circa 10 °C.Sono passati molti anni dal loro acquisto e non hanno mostrato segni di cedimento.Consigliato a tutti per far vivere più al lungo i nostri Raspberry.

Reçu rapidement et installé facilement sur le Raspberry PI 3 B+.Pâte thermique adhésive déjà intégrée sur les 4 composants, je n'ai eu aucun mal à intégré le Raspberry Pi 3 B+ dans un boitier standard.Fait bien sont job, diminue un peu la température comme demander.

Los compre para una rpi3 solo tengo puestos dos, el tercero en la caja oficial no cabe. He notado una disminución de la temperatura del dispositivo, indirectamente estop redunda en el rendimiento del dispositivo ya que no se deteriora al mantener la temperatura. La verdad que cumple con sus funciones perfectamente, el pegamento es potente y no se despega. Seajustan perfectamente al tamaño de los chips en los que hay que instalar.

Sehr leichte Montage der Kühlkörper am Rasberry PI 2 B. Es ist mit einem sehrdünnem 3M doppelseitigem Klebeband verklebt, was bedeutet man muss nur die andere Seite die Schutzfolie runter machen und richtig Zentrieren am Baustein und das war es schon. Achtung nur wundert euch nicht wer diese Kühlkörper für den neursten Rasberry PI 2 B kauft der hat nur 2 Chips die man bekleben kann ein dritter kleiner Kühlkörper bleibt übrig. Die zwei kleinen Kühlkörper sind gleich groß, daher wurst welchen ihr nimmt. Es gibt zwar einen dritten Chip an der unterseite aber der ist nicht gemeint erstens geht es sicht nicht von der höhe dann nicht mehr aus und zweitens der ist ein bischen größer als der Kühlkörper der übrig bleibt, vielleicht für früheres Modell von Rasberry Pi der 3 Chips hatte.Ja ansonsten gibt es nicht mehr viel zu schreiben da es ein ziemlich simples Teil ist der die Funktion hat die Wärme abzuleiten hat. Schauen wir mal im Langzeittest bis jetzt 100% erfüllt. Ich werde noch eine Rezession später schreiben und meine erfahrungen berichten.

lo he utilizado en una Raspberry Pi 3B Plus y funciona perfectamente se adhiere correctamente a los sitios que se indica en las fotos. Sobra una pieza para los modelos Raspberry Pi 3B Plus.Tengo la placa dentro de una caja y ayuda mucho.