Heath/Zenith HZ-4132-BK Black Bayside Mission Motion Activated Security Lantern

This was a replacement for exactly the same light. It looks great and the light is bright

I needed a couple of replacement fixtures for my condo that wouldn't blind my neighbors. These have great aesthetics, are simple to install and work wonderfully. I have had one for 4 years now and just purchased a second one. I love that I can keep these on motion sense all the time, or simply flip the light switch down and up to turn it on when I let my dogs out, and simply flip it off and on again to restore it to motion sensing mode.

Super easy to install (YouTube video) - had it fully installed in about 15 minutes. I like the functionality of the lamp - you can set the sensitivity of motion as well as for how long you want the light to stay on. You can also re-position the sensor on the light, if you’re installing it it in a corner or other angle. I installed this for my father to provide additional security/visibility on his front porch, and it works well! I reduced my overall rating by 1 star, as I do believe the quality could be improved. It looks nice but seems a little on the “cheap” side.

Very nice looking and easy to install

Boght 2, one of them arrived totally destroyed. They could have let the consumer assemble those glasses themselves and to save the hassel of running to Staple. But no, they had to be fully assemble. The entire light hold by a piece of cardboard inside the box without any foam or cushion just to save a few cents. Genius!!!The light itself - I have it set for 10 mins with motion sensitive on max. First off, it doesn't stay on for 10 minutes and only 8. The motion sensitivity listed range up to 60 FEET. Well, my old one look exactly the same as this except the housing is oval instead of square, and it does detect motion up to 60' just like it claim, so what happen to here Zenith Health? This will only dectect motion up to 15 feet with sensitivity set at MAX.Others problems I ran into when it was first install was. Light wouldn't stay on and go off after 30 seconds or so like it was in TEST MODE. After reading the troubleshooting step and it read...light may be in manual mode. To turn on or off manual mode, at the light switch turn it off for 90 seconds than back on within 2 seconds turn manual mode off. Seriously, why the F*** would anyone buy light motion detection and set it to manual mode? And why not just put it along with the timer switch?After all that was figured out. The light start to flash on/off... this time, according to the troubleshooting section, the light sensor could be effected by weather condition and or need to warm up. WOW!!!! I RIP the entire light off the wall and put it back in the box and back to Amazon it goes. What a POS and wasted of my time.

Nice light, works good, I'm happy with my purchase. There are two switches on the light, one for how long it stay lite and the other for sensitivity. That sensitivity setting also has one that says test. You can make the light turn on with the switch on that setting. You use it to make sure the light is connected correctly. You could probably use that to make it a light that turns on with the light switch if that whats you wanted, I personally wanted a motion sensor light.

Looks good and was easy to install BUT after about 2 weeks the light would start coming on for 5 or 10 seconds and then go off all through the evening. There was no motion that caused this activity!, I called their tech service number and told them of my complaint. They asked what type of bulb I was using and when I told them an LED they said that was the problem. I changed the bulb and the unit is now performing fine. The installation says nothing about NOT using an LED bulb.

Good looking easy install. On maximum sensitivity has a 30 ft range.

Very nice lights, easy to install, worked perfectly first time. The provided instructions aren't very comprehensive - for more advanced wiring (eg Master/Slave) there's a better manual on Heath Zenith's website. I also contacted them about LED bulbs - they're not intended to be used, but HZ said that if you use LED's approved by the NAM agencies and use DIMMABLE bulbs, the motion sensors usually work. I did that, and they DO work fine with the 60W LED's I installed.

Easy for me to install, didn't have any issues with my install contrary what others are saying, I think as long as you have a regular setup, switching out your lights should be a breeze. Will see tonight how the motion sensors work, but so far look good and reasonable price.Only thing I don't like is the bulbs are easy to remove, no glass at the bottom stopping anyone from stealing your bulbs a little too easily but still recommended. They could just unscrew everything anyway, so not a big deal.Update: Motion sensors seem to work well and turn on from about 20-25 feet away (length of my car) no problems.

Works well, simple but classic. Good price. Exactly what I was looking for.

Motion detection works good, and was easy to install.Worth the money, but must use the older style light bulbs.

Works good. However the top sensor part is locked straight. It really needs to be adjustable so you can turn it slightly down and to the side. My dogs go out back and it won't trigger the light to come on. I'm using the light now but I will have to get a different kind