Tub and Fiberglass Shower Repair Kit (Color Match), 3.7oz Porcelain Repair Kit, Porcelain Sink and Acrylic Bathtub Repair Kit White for Cracks Chips Dents Holes Almond/Biscuit/Bone

This worked well to repair a 3-4 inch crack in my shower wall. The product is easy to use but a little messy and very sticky. Be careful not to get it anywhere you don’t want it. I used several pairs of vinyl gloves. I was able to match the color perfectly. Beware, it only took 2 miniscule dots of the brown color to mix a light almond shade. It would be very easy to add too much color, so be cautious. The little spatula worked well to spread the product. Resist the temptation to put it on too thick. I waited 24 hours then sanded a little, as directed, but the sanding didn’t really do anything and seemed unnecessary so I didn’t go very far with that. Overall, the repair finished to be shiny and smooth. The repair is not very noticeable unless you look for it. Also, I only used about half the product, so I have some in reserve if I need it again. Would recommend!

Had a cracked and leaky drain in my fiberglass shower. Easy to follow directions led to a fixed and leak free drain. Thank you. Much cheaper than replacing the shower pan.

Quick, affordable and simply method to patch a tub. First time the product chipped off, but the second time I made sure it penetrated / clung to the crack and it's held up for a month or so at this point. Glad to have this, as I'm not super handy but was able to get the job done. One star off only because it was hard to sand down w/ the sandpaper provided.

This shower tub repair kit works really well for patching up cracks or holes. The color match and finish might not be perfect, especially if you’re not super handy, but it’s way better than leaving a hole.

Purchase this as my tub was starting to show visible little rust spots and little punctures on the floor when using this it works great very easy instruct however three stars due to the fact that after 6 to 8 months, the material peels off or removes from the tub. Went in the bath you can see the material float in the water.

I had several small chips in my almond tub. I got this to repair the chips.My process:1. I taped around the chips as close as possible using painters tape.2. I mixed the formula as instructed. To match my tub I only slightly put the tip of the toothpick in the brown...use less it will go a long way. I got very close to my almond with this amount.3. I used an ice cream stick to apply the formula to each chip..I took the side of the stick to remove the excess by sliding it across the filled area. You don't want it too heavy or you will need to sand it much more.4. I removed the tape around each chip immediately after I applied the formula and let dry 24 hrs. I left a tape marker next to the chips for reference so I could see where to sand the next day.5. The next day I used the 320 grit first and a wet napkin to lightly sand down and wipe each area. Once the areas were smooth, I used the 1000 grit to lightly sand the areas. Use a very light touch to sand. I wiped the area with a damp napkin in between sanding. It removes the particles and makes the area easier to sand. I was able to get a good color match for my tub.I was pleased overall with the ease of use and that the product worked fast. It dried to a hardened finish and held up well when I was sanding...staying in place. With time and patience, the product works as stated. Will see how it lasts when used.

I had accidentally damaged my "bisque" toilet tank lid, breaking four 1/2" size pieces off of the porcelain lip. The toilet is at least twenty years old and I did not want to replace the entire thing because of a few chips. After looking online, I found there are several products out there that are more like a thick touch-up paint and I needed something that was more like a pliable putty. I found this kit and decided to give it a try. There was more than a sufficient amount of the compound supplied in the kit and mixing two equal parts of it on an old plastic jar lid was easy with the "Popsicle" sticks supplied. I had to color it to the bisque color and that was a little tricky as just a speck of the supplied dye DRASTICALLY darkens the color. (My first try was way too dark.) Just the tip of a pointed toothpick stuck in the dye cup was all I needed. Once mixed, I pieced it back together and let it sit for the required twenty four hours. Sandpaper is supplied in the kit, but if you want a nice smooth finish I suggest you use a powered vibrator sander with fine grit sandpaper. The adhesion is excellent and it sands very well once thoroughly dried. The broken section is barely noticeable now. I used this on porcelain, but I'll bet this will work equally as well on all of the materials listed. I would definitely purchase this product again.

This is actually pretty darn easy to use. The only thing difficult is getting the color right and I think most of that is the fear of getting the color too dark. I actually ended up getting the color too light but I can always go back and add another layer of a bit more using a darker layer, if I decide to but I probably wont. The crack sealed really well. So ladies, don't be afraid. If I can do it, anybody can.