BSEED Dimmer Light Switch,Glass Touch Panel,LED Lights,No Neutral Wire Required,1 Gang 1 Way,86mm White

Easy to wire up and works perfectly. Looks good and the buttons are back lit which is a nice touch.

We bought this for our teenage son, new ceiling lamp with dim-able LED's that were very bright so rather than change the LED's we thought we would try this. Firstly - the bit you want to know - is it any good? Yes, it would seem it is. Very well made, and works as advertised. I've read another review that suggested you had to brighten all the way to max before dimming - that's not the case. Once powered up - and still off, a dim blue led shines from the switch (it is dim). touch once - the switch functions illuminating the lamp, and the backlit blue led glows bright. touch and hold - the lamp brightens until you release, touch and hold again - the lamp now dims until you release. tap once - light goes off (and back light ble led goes dim again). tap once again - it comes back on to your last saved level of brightness. Fitting - yes, the back part of this unit is deeper than a regular switch, so if you only have a shallow back box - you may need to change it, as it would happen - it fit ours fine. Instructions - could be better - one big sheet that covers a multitude of different switches/fittings - not the easiest of things to navigate. Things to note: The glass front, clips to a metal back plate. When you receive it, the back plate is behind the glass, but needs flipping over first - don't attach to the glass just yet though. The back plate has screw holes for using your standard back box screws - but these screws cant be accessed once the glass is clipped on. Also the power unit (transformer and switch assembly clips into the metal back plate - and then has a sticky pad that attaches to the glass. My fitting process was as follows: Locate the tab on the metal back plate edge, and point downwards, Ensure the back plate has been flipped over (so the screw mounting holes are further back - not at the front) Locate the transformer into the back plate - requires a firm snap into place at all four corners Wire the transformer/metal back plate assembly Screw the metal back plate into place - doesn't need to be rock tight. Peel off the sticky pad covering the 'switch' on the front of the transformer. On the plastic edge of the glass backing, there is a notch which the tab of the metal back plate locates Align the notch/tab and push firmly so that the glass snaps into place top & bottom. Power up - leave for 2 mins (as per instructions) Good to go. Would i buy again? Yes, if the unit proves to be reliable/resilient, and seems to last up to the riggers of a teenager (we'll give it a couple of months first!) then i would buy again. Hope this helps. Update: 3 years in, and still working without issues. Good product.

Ok but will not work with certain lamps

bought 2 of these dimmer switches but only 1 worked. Will give a replacement a try

I also bought the more expensive CBINGO unit this one required more assembly. It comes supplied with the metal bracket attached to the glass panel instead of the dimmer unit. For now you need to remove this. Use a flat blade screwdriver to wiggle it off the glass panel. I suggest you practice snapping it back on a few times so you know how to do that when the dimmer is screwed into the wall. I didn't have enough depth in the wall to sit it flush and WORSE the box was deeper on one side than the other making aligning that screw hole impossible! Adding a spacer solved that and enabled me to latch the glass panel on. As the spacer is cheap buy one just in case. "Schneider-Electric 1 Gang Spacer black" SPACER INSTALLATION TIP: To align the screw holes position, first screw the spacer onto the wall and then mark around it's outline or do as I did sellotape the outside of the spacer to the wall. With the screws then removed you can then wire up and install the dimmer switch.

Instructions for fitting could be clearer with an A side vs B side on the metal plate, but the biggest issue is an LED adaptor with no fitting instructions. I cannot dim my LED light and don't know if it's my error or component capability.

good item

Extremely easy to install and worked instantly.

en remplacement d'un système variateur à molette défectueux pour 3 éclairages; très facile à installer malgré un mode d'emploi en anglais peu compréhensible; 2 fils seulement à brancher, plaque et système de fixation solide et de bonne qualité; faible encombrement de la partie arrière qui rentre donc facilement dans l'encastrement; une fois branché, très esthétique surtout la nuit avec les leds bleus et le fonctionnement du variateur impeccable; donc le plus: esthétique, aspect solide et connexion facile; le moins: prix un peu élevé et notice bizarre. par contre, il y a une sorte de condensateur présent dans la boite avec le modèle; je l'ai monté sans, ça fonctionne, mais quelle est son utilité? si quelqu'un a la réponse, je suis preneur.

Hög kvalitet på brytaren. Fungerar bra. Lätt att tända/släcka med touch. Dimmer fungerar utan flimmer. Bakgrundbeslysning är lagom stark.

Works good

Goed

Sieht gut aus und macht was es soll. Preislich auch sehr gut und qualitativ hochwertig.