MAXRACING2" Leveling Kit Compatible with 2007-2026 Chevy Silverado 1500 Avalanche Suburban Tahoe/GMC Sierra Yukon XL1500

Excellent leveling kit. I installed these on a 2018 Silverado. I'm running 33x12.5R22 mud tires with Yukon Denali 22in wheels (+24 offset, 5.94 backspacing) and no rub. Before the alignment the tires slightly rubbed the sway bar at full lock and didn't rub at all against the fender liner. After the alignment with the caster angle adjusted, there was no rub at all. Be sure to tell the shop to adjust the caster, not all shops will do this without being asked. (Even though they should without being asked) My shop specializes in off-road trucks and they set my caster at +3.7°, which feels about perfect. However, I do have larger upper control arms, so your angle may be different if you keep the factory uppers.I installed larger upper control arms made for 2in to 4in of lift. With the larger control arms, the shop that did the alignment said he nearly maxed out the adjustment on caster, but it was set where it needed to be. He said the factory control arms probably would have adjusted to the correct caster too, but I personally recommend upper control arms since the factory stamped steel upper control arms and factory upper ball joint can fail over time with the lift. There's a lot of geometry change going on and the upper ball joint just can't articulate enough at full extension. Which means it can snap if the wheel extends hard enough.These 2in leveling blocks leveled the truck perfectly flat with no change in the rear. 2.5in is the max that can be added to the front without lowering the transfer case as well as other mods. So, 2in is a good comfortable lift height to simply level the truck with minimal other mods. But again, I do recommend upper control arms. I also recommend sway bar end links since the factory ones had seized and needed to be cut off. (Also, aftermarket sway bar end links improved the smoothness of the suspension so much, and they're not expensive, so go ahead and order them). I used a 4in cutoff saw, and still had to hit the factory ones with a blowtorch to melt the plastic enough to get the bolt out of it. They were trash. The replacement went in without issue.Install was easy. 1. Remove the 21mm nut on the tie rod, tap out and push aside. 2. Remove (or cut off) the sway bar end links. 3. Remove both lower bolts on the strut. Use a pry bar under the strut and pry against the lower control arm to slide the spacer in, then use a pry bar in the space between the upper control arm and the bottom of the spring to push the bottom of the strut inward toward the holes to align them. (With the spacers the bottom of the strut will want to push out toward you, so you'll need to pry it back to slot the bolt in) It takes a little work and a bit of luck to get the first bolt hole lined up. A second set of hands would have gone a long way to make it easier. 4. Insert bolts/washers/nut. Torque the hell out of them. Then retorque after 20 miles and 100 miles. Since you won't be removing the wheel hub assembly, on 4wd the CV axle will be in the way of one of the bolts. Just insert it from the bottom. The bolt cleared on mine but it was close. If needed cut the bolt a smidge. 5. Reinstall the sway bar end links, reinstall 21mm nut on tie rod (you may need a 10mm wrench to keep the ball joint from spinning. I used an impact gun and didn't need a wrench.)An additional note on clearance, I'm installing 2in wheel spacers, so I'll need to do the NorCal mod from rough country to prevent rubbing on the rear of the fender liner. If your wheels have a large offset they'll rub some with 33s. (Actually diameter of my tires is 32.75in)Hope that helps! Great product, great price.

CAN WORK WITH FACTORY GM MagneRide/ GM air shocks PLEASE READ BEFORE INSTALLINGI installed on 2018 Yukon XL Denali with factory suspension.This will lift the rear 2". The factory ride height sensor rods, for the rear, are both 3.5" long from center to center of the ball sockets. I measured ride height sensor angle prior to installing this lift kit. POST installation to make the sensor angle match OEM position you will need longer sensor rods. The new rod will need to be 3.8" long from center to center of the ball sockets.I purchased 2 of the GM part# 25379115 here on Amazon. I cut each one down so each side is 1.9" from center of ball socket to the cut end of the rod. I threaded each end with a 10-24 die. I used a 10-24 coupling nut from Lowe's part# 423510. I added blue loctite and evenly threaded both ends into coupling nut and popped back onto ball pivots.The rear end of the Yukon is lifted, but the MagneRide system thinks it is at factory height. I did drive the Yukon for several miles before making this ride height modification. I never had a fault code or issue from the computers. It did "feel" like the rear end was stiffer, but I have no data to confirm this. Post ride height sensor rod modification the Yukon feels like it did from the factory.

Worked great

Originally installed 2.5 bottom spacer on my 2024 Silverado 1500 4x4. Very hard install being 4x4, rougher ride, and overall bad geometry for truck.I reinstalled the 1.5 maxracing top spacer and absolutely love. The rear sits right at .5 inches taller in rear, which is exactly what I wanted, and the truck rights like factory.At 1.5 you are still in the factory “safe zone” and don’t need to consider replacing your upper control arms. For a 4x4 I would only recommend top strut level, period.You also do NOT have to cut factory strut bolts to install top spacer. Huge plus.

I purchased the 2” leveling kit. My husband said it was fairly easy to install. He had it completed in about an hour. Broke a sway bar link in the process but that’s not uncommon. My suburban looks much better.

Just as expected! Came with all the correct hardware. Arrived right on time as advertised! I have bought a couple of products from Maxracing and have been pleased with it all.

Installed this kit yesterday. Everything fit as it should. Zero issues. My 2024 Silverado 1500 is set up for overlanding/camping. My rear was sitting 1” lower than the front and would bottom out on the bump stops with the added weight. I added these 2” blocks also added shock extensions. This brought it back to the factory rake. It is sitting 2.25” higher in the rear than what it was. The build quality of the blocks was good. Real thick steel. Welds were so/so. A complaint I have is that the blocks should be marked which side faces the front. The instructions just say the smaller end faces the front. This gave my truck the look I wanted. Feels like it’s riding like a truck again and not a squatted dog. No alignment issues. For the moneys I would highly recommend these for anyone trying to achieve a lift. Or in the same boat as me as carrying a lot of cargo on a daily basis. Can’t beat the price.

Have had this installed on my truck for a long time and it has help up and rides amazing! I recommend this 100% if you’re looking for an affordable but great quality leveling kit!