Toilet Handle Replacement Flush Lever - by LDR Global, Repair Replace Tank Flusher Handles, Universal Mount Fits Front Side and Angle Mounts, Chrome Finish Metal Levers

I gave this product 5 stars ONLY because it is well made and appears to be a quality product. However, it WILL NOT FIT a side or angle mount toilet. I have a Mechanical Engineering degree from Clemson University and can not get this product to operate properly without significantly modifying the hardware. In order for the flush handle to flush the toilet, the arm attached to the flapper valve MUST move from DOWN to UP. The only way this product will do that is if the handle is mounted in the FRONT of the toilet tank. When mounting this product on the SIDE, the handle will move the arm that attaches to the flapper valve in a SIDEWAYS direction (not UP and DOWN). Because the SIDEWAYS direction contains a small UP and DOWN component, the arm moves significantly from BACK to FRONT of the toilet tank and UP and DOWN about 1/2 inch -- this is on enough to open the flapper valve significantly enough to flush the toilet. As I said, I could probably grab a couple of vice grips and bend and rotate the arm significantly enough to produce the required UP and DOWN movement to make it work. But, I'm not doing that for obvious reasons. After doing additional research on Amazon, I decided to give the KORKY STRONGARM TANK FLUSH HANDLE a try. The video attached to the handle looks promising. At least, it shows and UP and DOWN movement rather than the rotational motion I get with this product. Again, this handle is well made, but I would only us it on a FRONT mounted position.

These handles are very classy. We recently moved to a new home that had all sorts of plastic toilet levers. I installed this lever in all of the bathrooms because it matched the oil rubbed bronze door handles and gave it a little extra luxurious boost. They are made of heavy metal. I would totally buy them again.

Nice handle with good heft and seems solid. However after installation I noticed the fit is not snug and the handle “jiggles” in the socket more than I think would be acceptable on a nice toilet.Confident it’s not installer error and have attempted my own fix using a couple of #6 neoprene washer on the brass screw where it contacts the handle (neoprene so it doesn’t make a metal to metal contact sound).So after all that I just said screw it and kept it. Not worth fishing it out of a toilet tank to return it. But I wouldn’t buy it again.Not much else one can say about a toilet flusher.

This was the first home repair project I’ve done on my own(the old handle on my toilet came loose, so I used museum putty for a temporary solution and put this handle on my toilet today), and yet installing this was a breeze. I had to use a clip to secure the chain, and a crescent wrench to uninstall the old hardware and make sure the new handle was secure, but other than that no extra tools were required, and the instructions made the installation incredibly easy for me despite my lack of lack of experience with repairs.The handle itself is slightly thicker than I might have liked it to be, but it still looks nice, and based on the pieces that came with the old handle compared to the new handle, I think the new handle should last a lot longer.

THE PRODUCT APPEARED TO BE VERY HIGH QUALITY. I SAY APPEARED BECAUSE I COULDNT INSTALL IT. I HAD NOT MEASURED THE OPENING TO THE TANK AND PRODUCT WAS A LITTLE TOO LARGE, WHICH WAS TOO BAD BECAUSE IT IS NICE. I GAVE A BAD REVIEW DUE to THE NO RETURN POLICY. IMMEDIATELY AFTER MY POST, I WAS CONTACTED BY VANESSA FROM JACKSON SUPPLIES. AFTER ONE EMAIL, SHE RESOLVED MY PROBLEM WITH A REFUND. JUST MAKE SURE IT FITS YOUR MODEL TANK AND YOU WILL BE HAPPY WITH THIS LEVER

I was wary of ordering this online as wasn’t sure of the quality. Have no fear, this is very high quality. I appreciated the angle in the handle for install as that’s how my current one was and I didn’t want to have to reconfigure everything on the inside of the toilet tank. Very high end quality product and super easy to install even if you aren’t a super professional handy man. I did it in about 15 minutes. Love the quality and it matches the other fixtures in my bathroom that were high end. I installed it about two months ago and no issues at all. Holding up well.

This really pulled the bathroom look together.its a simple way to add interest and pull together a look in a room.subtle, durable and i highly recommend!I included a before and after photo of my half bath renovation. You can check out more of my DIY home renovation projects on my instagram_taylor_bee_ or youtube/TaylorBee !!! :)

This is a very sturdy handle made of brass and steel/aluminum? It’s the 2nd one I’ve installed on this toilet in 3-4 years. The other was exactly as this one and the only defect was it had a weak spot in the handle where the handle meets the body, where it actually snapped in two pieces. I find it very unusual and odd as it’s extremely heavy and seems like good quality. I’m not sure how it happened, but it did during a flush. It wasn’t abused so there you have it. I’m trying again with the same product because I believe it was an odd flaw.Thank you 🙏