OzniumBRIGHTEST Light Bolt - Flush Mount 12V LED Light for Bumper, Grille, Cars Interior, Dash, Ambient Lighting, Motorcycle w/SLEEK Aluminum Housing & Screw Nut (6 mm Black, Red LED)

The media could not be loaded. I bought these to add to the skeleton I mounted to my radio control mower. I bought the 11mm red version, and am delighted with how they look. The pictures and video do not do these justice. They look far better in person!I was concerned about these getting too hot and melting the plastic, so I wired them (1 pair) in series with the voltmeter, (rather than in parallel) on a 14v circuit. This reduced the voltage (and heat) by 8v, and these are still plenty bright for my needs.

I installed this on my tractor as an ignition light, so it switches on with the key. At the end of each cutting season, I shut off the fuel and run the tractor carb out of gas. I've forgotten to turn off the key the past few seasons, only to be greeted by a dead battery the following spring. This LED light should be a nice visual reminder, as it is nice and bright.

The media could not be loaded. I purchased several of the 6mm blue versions (with no lens) to have installed inside my 2013 Ford Fusion for ambient lights during night driving... and I love them!Don't be fooled by their extremely small and compact size: These things pack a bunch of light!I first bought one LED of each size (6, 11, and 16mm) in the blue color to test and see how big and where they should go in my car.I did this by waiting for it to get dark, buying a 12v cigarette lighter adapter to externally power the lights and taping them all around the inside of my car where I would like for them to go.I'm glad I did this test before drilling any holes in my vehicle as not only did I find I wasn't a fan of having lights illuminate my foot wells (I could see every speck of dirt on my floor mats which would drive my OCD crazy) but I also quickly found that the 11 and 16mm LEDs are too powerful/bright and that the 6mm would be more than enough to light the inside of the vehicle without glare or being distracting while night driving.This also worked out nicely since the 6mm ones are so small it made them much easier to install and discretely hide from sight.Ultimately I decided to install seven of the 6mm LED bolts: One in each of my four doors, one in each of the two front cup holders, and one in the center cubbyhole underneath the dash.Once I found how many and where each of the 6mm LEDs needed to go I had them professionally installed and couldn't be happier! On my car, they fade on when I open any of the doors (so they act as a courtesy lights... especially the ones that are installed in the doors) and fade off a minute after the engine is turned off or when I lock my doors exiting the vehicles.The only criticism I have with these tiny LED bolts is how small the "lip" is around the light's source. I bought the 6mm drill bit from Oznium for the install but the "lip" that is meant to hold and keep the LED from slipping through the hole is so little I didn't trust it to securely keep it and place. So if there's one piece of advice for improvement it'd be to make that lip a bit bigger for peace of mind.Because of that I went to my local hardware store and bought rubber washers that fit very snug and secure around the bolts to ensure no chance of the tiny LEDs slipping through their holes.Check out the ATTACHED VIDEO to see them in action!ATTACHED IMAGES: For the "test phase" I powered the 6mm LED bolts through a cigarette lighter adapter and taped them all around my car to see how many and where I would like them to be installed. I then drove around at night with them taped and turned on to make sure they wouldn't distract me while driving. After trial and error with quantity and their positioning I was able to proceed with getting them permanently installed.

These worked perfect for my rear third brake light setup, I will be working them up to be brake lights. They are bright for the size. I would recommend adding a little glue or loctite around it to keep it from unsrewing.

Fit perfect for my project, simple install and light is bright for its size. One downside is it only comes with one nut to thread on the back so I imagine it will loosen over time.

The color tone is distinctiv, Soft lighting

I used these as a footwell lighting solution in my 13 Cadillac Escalade. The lights are plenty bright, the cool white is a great match for the led interior lights, they’re small and inconspicuous, and the wires are heavy enough to crimp without folding them over. I connected them via a T-tap to the under dash courtesy light wire so they function with the courtesy/dome lamps when the doors are opened or when I turn on the all-dome lights and they function with the key fob too. I like how they dim/fade to black with the OEMs too! Now I can actually find things when they fall to the floor board! Time will tell how they hold up so I’ll have to revisit that at a later time… but they’re pretty solid little units so I have high expectations.

Brightness is not diminished even when viewed from a side angle. Good replacement for a warning light that came with a tiny light bulb.I left this on all day in summer at 14.7 volts (nominal for a 12 volt system with the engine running); it got just a bit hot but suffered no damage. If installing in a plastic surface I would suggest using an aluminum washer to provide a bit of heat sink and should be no problem. Comes with a lot of wire but little stripped; strip carefully, the conductors are rather thin and close together.

These lights are small small. But they are bright so they do the job as signal lights for me.

Not as bright as I was hoping for.

Flush mounted with no lens looks mint clean and doesn't protrude.Very durable design. Tough and hard.They are flood lights, so the light covers a wider area. Just need to see them in during a dark night.Next project is filling the round indent behind the handle with light

Lights are made of metal and feel very durable. I used them as grill accent lights and wiring them in was super simple once you figure out what you are doing. Would be nice if the provided wire was slightly longer since I had to extend it to reach my fuse box but they are exactly what I was looking for.

So far so good. Mounts flush. Bright. Seems to be holding up. Great use for an aftermarket puddle light installation. Would recommend. Shipping was fast.