KABA Lite PETG CNC Case - Improved Protection, Dustproof, Compatible with 3018-PRO/3018/3018-MX3/3018-PROVer/1810-PRO, 450 x 390 x 300 mm

The media could not be loaded. My KABA Lite Exclosure arrive yesterday and I got around to putting it together today. It took longer to get it all unwrapped than it did to assemble. It was almost too well wrapped! I would rather that than having it arrive damaged. I will say the instructions are a bit lacking but its a box. Not to difficult to figure out how it goes together. With the thin plastic I was worried it would be harder to keep aligned while assembling but it wasn't. It all slid together easily. Quick shipping and easy assembly makes this a good buy.

Have this sitting on my desk beside my laptop - I can run my carves with my 3018 and control it from the laptop while being able to watch to make sure all is well - One thing I did notice is there is the slightest bit of dust that can get out the very top of the front door/window - to take care of that I take two very small pieces of blue painters tape and put on the top to close the tiny gap there

Leaves some to be desired in how easy or difficult the panels are to detach. Also doesn't do a lot of good if you happen to purchase the 3040 extension kit (which I did after I bought this). It worked really well before then with my Genmitsu 3018 prover, keeping dust in and suppressing the noise just a little. Was great when I did some board surfacing previously, but that makes so much more dust than anything else does. I could imagine this being very important if you had your mill in a finished area (mine is in the garage) because it traps dust well if you use all the sticky pad strips they sent with it.You probably don't need this, however. It's a good value, does what it says and that's about it. Makes adjusting your stock or anything else a little difficult too because the panels don't easily come off, except for the door. Further, the back panel with the small hole for wires is what really ruins this for me now that I've upgraded. Based on that design, this feels like a permanent upgrade but absolutely shouldn't. Remember when I said it makes adjusting your stock difficult? Well, now imagine you want to move your unit, because my space is so narrow, I have to disconnect all the wires to remove the box, move the mill and then put it all back. Back and front should pop off with magnets in my opinion. This could also make it an easy transition to the larger size mill or more options of where to place your box. Oh, and it's also just barely large enough for the stock 3018, so I had a couple times where my stock was hanging off the bed and would crash into the door and pop it off - removable back would help here too. Getting the Z probe out was a pain with this on as well. Finally, it's made of aluminum and strong enough for its purpose, but not much more. I accidentally bent the front top crossbar by laying my arm on it while trying to plug something in.Ok, so all that said, get it if dust is a big concern AND you don't plan to upgrade later. It's a great idea in theory, but clunky and big trying to actually put it into practice. I don't think I will try to and add it back, even after adjustments, so I'm going to try and convert it into a 'hood' to capture and vent my laser exhaust.

This cover is fairly cheaply constructed. It's somewhat easy to put together although it's a bit of a trick to get all the panels and the framework to line up as you are trying to assemble it It's basically hammered together with a rubber mallet to keep it in place so you could break it apart pretty easy but also makes it prone to falling apart if you move it around a lot. For the money it's not too bad but if you want something sturdier, I would probably not recommend this product

It was very nice but it was to small for CNC machine and plastic was pretty light

Quality product. Easy to assemble.

Este producto lo voy a usar para mis trabajos de juguetes de madera que construyo (a escala) con base a planos especificados

The Good - I have no serious complaints. This cover provides the protection it claims and some noise reduction, so I give it 4-stars.The Bad - The material feels flimsy and the front door is easily knocked off. There's not a lot of space inside to add anything to the CNC machine (like a vacuum system for debris and dust). For what it is, it seems expensive.