DAFUNY 8 Pack Rubber Case Feet + 2 Set (20pcs) Repair Replacement Screws Set + 1pcs 5-Point Pentalobe Screwdriver Compatible with Unibody MacBook Retina for A1425 A1502 A1398 13" 15" Bottom Case

This makes me feel like I’m an Apple Genius Guy! I had so much fun replacing the feet and cleaning my years collection of dust in my MacBook!Here are the foolproof steps!1. Place your MacBook on a sturdy desk preferably over a mat/towel so it wont move. Have good lighting over it too for maximum visibility.2. Start taking off all 10 screws (2 short, 8 long) and put each of them aside according to where they are on your MacBook. This helps remembering which ones they are.3. Slowly take off the back panel and you should hear two clips unlatch from the middle. These latches are to hold the back panel in place.4. Clean out all the dust using a blower, canned air, or makeup brushes! This is the fun part!5. On the back panel, remove the old feet and take off all the black plastic nubs that are in each of the holes. For the back two ones, cut an X with a knife to release the nubs (use the screwdriver to poke them out). Clean out the glue residue with nail polish remover/rubbing alcohol. I also washed the back panel with soapy warm water.6. Remove new feets from the plastic container and align the big & small dots. Press firmly. I heated them up with hair dryer to solidify the glue even more.7. Align the back panel with your MacBook back and make sure the two latches from earlier click before you screw it back all together.8. I used the same screws to screw back the back panel since they are still good. Don’t worry about using new/old screws as long as they fit flush with the MacBook!9. Now your MacBook will not move around on the table anymore!!Overall review: this kit is amazing, and definitely would recommend anyone looking for feet replacement. The whole process took 10-15min and now I feel like I have a new MacBook!

OEM is definitely plastic, while this product is just rubber, so expect a different feel after you put it on. With OEM, you could easily slide your computer around. With this, expect some resistance since it's rubber. At first, your mac might be elevated a little higher that you're used to, but it should level out after some time.When installing, remember to remove all residue from previous "feet" so use isopropyl alcohol if needed. With OEM, there might be a very thin sticker left behind after removing the "feet" so just pick it and take that out. The new "feet" should be put on directly to the aluminum casing, and you really only have one shot to put it in so be careful and make sure you're happy with the positioning before firmly pressing it against the aluminum casing.It was nice they included new screws, but I didn't need them.

Other than taking 3 weeks to arrive, I am happy with the installation. We'll see how long it lasts. I had one foot wear off my mid-2014 13" MBP. Since the kit came with 2 full sets I replaced all 4 feet. It did take a good bit of cleaning with rubbing alcohol to get the old goop off. Old feet crumbled into many pieces. There was a clear round disc the size of the foot that you can't readily see that was the holder of the adhesive. If you scrape the perimeter with your fingernail or a blade you can peel it up and most of the goop will come up. Lined up new feet with tabs and they went on fine. Wiggled them a bit to be sure center post went in holes okay. Then just press hard. I used the new screws because I had them and my old ones were a little dirty although I'm sure they would have worked fine. Saved them for spares. Took a bit of wiggling to get the 2 center clips of the laptop back to reseat in their slots. Took maybe 15 minutes total if that much. All good now - laptop stays put on the beanbag lap pad I use.

I noticed that one rubber foot was missing on my 13" MacBook Pro and so didn't sit balanced on a desk. I imagined finding a replacement and installing it might pose a hassle though felt sure Amazon might list some kind of kit. There were, in fact, several to choose from and I picked this one based on the positive reviews. I could not be more satisfied. Opening up the innards of your laptop is not for the faint of heart and I always expect something will spring out and create a costly repair. but there was zero drama. Everything you need is provided and swapping out for the new rubber foot was both quick and simple and now looks like new. It's perhaps inevitable that with the constant wear and tear, especially if you're constantly transporting your MacBook Pro around, that eventually you'll notice a foot has been lopped off. If so, don't hesitate to send for this kit to do the repair yourself. Extremely simple.

My poor MacBook was in need of new feet so here I am. The kit includes two complete sets of screws and feet. The screws seem to be better quality than what came out. And there was even a magnetised screwdriver, which was much appreciated. When dealing with tiny screws a magnet really helps.The bad news is that no instructions are included. I had to come back to the product listing to verify which screws went where. They are colour coded, which is helpful, but if you don’t know which go where it doesn’t help much. It could be printed on something the size of a business card.I’m happy to have found this set and hope it lasts a long time. I hope this is helpful to someone.

While it is not generally necessary to unscrew the cover, it takes only few minutes, and it is a good occasion to vacuum the dust inside.If there are pieces of the old rubber feet stuck in the central holes (there was one in my mid 2014 MBP 15), removing the cover does help to clean the holes.Included screwdriver works great.Note that two screws close to the "MacBook Pro" sign - at the screen hinge - are shorter than others, keep them aside.Installed three new feet, and kept one old, since it is still in place. The new ones are exactly the same size and shape as the old one, perfect match.Time will tell how long will they stay, but there is a second set included, just in case.

A perfect OEM replacement for my MacBook. Total instal time was 20 minutes. I recommend having a small soft bristle brush and maybe a can of compressed air to clean all the dust out of the fans while you have the case open. Also I used some isopropyl alcohol to clean the case where the new feet stick down.Easy as 1..2..3.. to install and just like OEM, I couldn't be happier and recommend this product.

The product is good. BUT!!!The two footer near speakers (A1502) are covered by black shielding tapes. You will have to peel it off to remove the broken footers inside. The peeled off black tapes does NOT stick back. I had to buy ESD tapes to fix this. The black tapes are to prevent circuitry from shorting out.Be sure you know this. I learnt the hard way.

Rubber feet feel just like the originals and fit perfectly and stick very well. Included 5-point pentalope screw driver, although not high-quality, did an awesome job. I did not use any of the screws as I re-used the original ones from the case.

Great quality screws and pads. Pads feel good rubber to me.The screwdriver - which I initially didn't need - was a big saver for me. The old screws were damaged using my old screwdriver to the point I got scared if I could remove them or not, but the provided screw driver did better and it saved me!

Lo compré porque necesitaba reparar la Macbook pro de mi novia y fue de bastante utilizar, el material no se ve tan resistente pero es bueno para salir de apuros. Vale la pena porque viene con esos extras, un cepillo y algunos tornillos de repuesto más el antiderrapante de la macbook.