EVIL ENERGY Exhaust Hanger Rubber Insulator Bushing Mount 2 Holes

I liked everything EXCEPT I ordered the wrong size. If I had ordered the correct size everything would be smooth sailing. That's my fault. Their product came in quick, looked like typical exhaust hangar. I mean...what do you expect Amazon? It would work fabulously if I ordered the right size.Why didnt I send it back? Because I drank beer and lost them. Both. It was cheap AF so it didnt bother me. Seemed nice. Fast and cheap just like...well you know.

Installation was a breeze, used silicon grease, a jack to take weight off the exhaust and these slipped right into place. Getting the old dried ones off is the hardest part, use a serrated blade to cut the high density rubber.

Tail pipe( factory installed ) not aligned to fit factory 2 hole hanger. Extra holes allowed to relieve tension from FACTORY misaligned tailpipe. Because these are thinner I used 2. Fit on hanger pins perfectly. ( pre lubed pins)Improvement I suggest is add another hole and maybe sell a thicker hanger?I am very happy and the fast delivery. I also previously ordered a pair of 2 hole ( original eqpt. ) hanger and had to jack tailpipe up to install the O. E. hanger. After that, I realized that the misalignment is reason the hanger failed.Lucky the extra hole hanger sold as pair, used both. So happy I kept the 2 hole hangers just incase they are needed later on.

I guess Ford discontinued the exhaust insulator that secures the tailpipe to hanger from the frame on our 2004 Explorer 4.0L. The metal ring on my original had rusted out and I saw this one with approximately the same 2" distance between the holes so I gave it a try.I had a concern that the diameter of the hanger from the frame was too large for the insulator, but I put a dab of silicon grease on the rubber, slid it on both hangers and was installed in under 15 seconds.

After a couple of months of use on an aftermarket exhaust setup on a daily driven RSX, these have held up well and adequately suspended the muffler and pipes.Will update if they fall apart in a year!

This was just the thing while replacing the exhaust on my Jeep Wrangler TJ. I had installed a 3” lift which required dropping my transmission about an inch. This tilts the drivetrain and had put exhaust system in a bit of a strain as well. This product allowed me to let the tail pipe hang a little lower and take pressure off head pipe and catalytic converter flange connection. I used silicone paste to lube hangers and allowed me to easily install and remove if needed to reposition.

So easy had installed in 5 or 10 minutes remember the old one rooted away like butter...thank you a whole lot will order 2 more I may need to change them all..And for that price come on you can not lose...Thank you again.....

Replaced the too soft OEM rubber exhaust hanger behind the muffler with this hanger made with firmer rubber. The firmer rubber of this exhaust hanger prevents the over-the axle exhaust pipe from rubbing and rattling against the rear axle crossmember.

My muffler recently separated (rusted through) so I bought a walker as a replacement by the hangers were different and I had a hard time matching up the insulator brackets. I ordered these which gave me an extra room to work with. They've been installed for 2 weeks now with no issues. They look just like the manufacturer ones on my vehicle, just longer with extra holes.

I bought these as it seems that the reviews say it worked well for their car. I was hoping to get the same result as I've seen two other reviews with the same car I have.I was surprised to find out that they were softer than stock. My purpose of buying these was to keep my exhaust from touching the plastic bumper which it had started to melt when the car goes through bumps.I had to make use of them so I couldn't waste my money.. I had to use the stock ones that came with the car along with these ones.Don't buy this product if you're looking for something stiffer than stock.

bought this hanger for my 2008 chev avalanche. The hanger worked perfectly, solid and firm.Would definitely buy this item again. Thanks!

Rubber looks to be quality , this model is nice for custom exhaust , it can be long or short ,and if you instal it short you can flip it to be stiffer or softer to tune placement and vibrations as you wish

I would of preferred to get my items VS a sticker with their brand name on it. A sticker won’t hold my exhaust up very well.