Pocket-Riveted Design Wheel Fender Flares Compatible with 09-10 Dodge Ram 1500 11-18 Ram 1500 Fleetside Bed, Black, WF-81009-MBK

So these took roughly an hour to install. Particularly because each little bolt in each hole took a while. But all you need is an 8mm wrench or socket, 13mm socket or wrench, and a stubby Phillips head screw driver and these slap right on. I had some fender well rust happening and without spending thousands on fixing it, I covered then up very cost effectively. Amazon is screwed up or I could attach a couple of pics

Correcto

Great for the money not a 15min job but if I could do it so could you..my 2018 ram looks better than ever

The rubber strip they give you to go against the bed doesn't stay on. Uses door edging instead. Once on it doesn't line up. Bout a 1/8" gap in front and 1/4" gag in back . Don't waste your time or money on these

I was back and forth between 2 and 3 stars for these. I bought these because they were marked to fit my 2017 Ram 1500, and I wanted the pocket rivet design. Out of the box, they felt fairly flimsy, but I figured once they’re bolted on that would go away. The 2 page instruction pamphlet looked like someone should’ve changed the toner cartridge in the copier about 200 pages ago. All the writing was faded and distorted. Placing all the bolts and nuts (34 total), as well as the edge trim took about 1.5 hours. Installing them on the truck took about 1 hour. I figured these would bolt on cleanly since they’re made for my truck, but nope. LOTS of trimming will be needed to correctly fit the body contours. The rear passenger flare is even missing a screw hole. From a distance, these flares look awesome, but up close you can tell they are cheap and don’t fit well. I guess you get what you pay for. I’m just hoping at this point they last at least a year. There are also holes that should have rivet pins (which other manufactures include) that weren’t included with these. The only other positive is that they are short enough to not hit the hemi badge on the fenders, so thankfully I didn’t need to remove those. All in all, I’ll keep them on since I spent so much time putting them together, but I do regret purchasing these.

I was really skeptical about ordering these because of the price. But I did anyway. Very pleased with them. Extra hardware so didn’t have to worry about getting more. Fastened right into existing mounting screw holes.

Looks good, posting a pic so y’all with 4th gens can see what they look like.

First off, no directions. If you know what you are doing, not a huge deal. Bigger issue is the screws that are meant for the outer part that secure them into the fender wells. They are WAY too short to do any good whatsoever. I had to buy M8 20 mm screws separately to get the front done. Go to the rear wheel, and due to there being an extra piece of sheet metal up in the rear bed, the 20 mm I bought are too short as well. So, I just had to order more M8 but this time 45 mm in order to get all the way through so I could attach the lock nuts. Very poorly put together as far as parts are concerned, coupled with lack of actual directions. You may want to look else where, save yourself the hassle of having to order additional parts to mount these.

I have purchased alot of these fender flairs for all kinds of different trucks. This set was by far the toughest to install. the rears were easy no problem. Fronts were a pain in the ass! Had to trim the flairs, heat them up with heat gun just to get them to fit inside the front door opening!! bad bad design. Good to you all that have never install fender flairs before. And to top it off these were the most expensive i have bought as well ! Never again…

they look great but some spots they stick out from the truck. and not enough adhesive had to spend more money to get them to sit right.

Was what we expected EXCEPT FOR no instruction and screw not included the couple of screws that were included were too small to be of any use. Think about buying this if you are not experienced in installing this product

Main thing is they don’t fit. The pic doesn’t do justice. After one drive they all have 1/4 to 1/2 inch gaps and buckling. They don’t line up properly on the front with bumper/headlight area. Pretty sure these were used. Box was taped up and destroyed on one side. They’re all scratched and gashes in them. No instructions. Less then half the hardware. Which I ended up buying myself because I needed them on the truck. And the rubber trim was twisted and knotted wouldn’t stay straight to install. It’s to bad because they seem to be a good quality flare

I received this fender flare kit by DNA came with no instructions Also not enough hardware The nuts and bolts that go into the holes of the plastic was small the bolts couldn’t fit into the hole, but some could. Never came with enough metal tabs And now have to figure something out to try and mount this to the truck, I have managed to get the rubber liner on the edges of the fender flare This is a long process when you don’t have all the supply’s to install.