2.4GHz WLAN Router/Bridge/Repeater VAR11N-300

This device does exactly what it says on the tin. In my case, that was to set it up as an ethernet to WiFi bridge to my main broadband router (that supplies our internet connectivity) for my Humax DTR-T1000 Youview box, which only has an ethernet network connection, as I wanted to move it to another room where there was no physical network connection. The instruction booklet that came with it covered all the options that this device was capable of and was fairly well written and easy to understand. Within a very short time, I managed to set the device up as bridge/repeater (but I also chose to suppress its associated hotspot that was also available) back to/for my main router (using my smartphone to connect to it initially) then rebooted the device to change its configuration. I finally unplugged it from the USB power connection I was using (just for power) and plugged both cables into the T1000's ethernet and USB ports on its rear. It immediately powered up and "voila!", internet connectivity wirelessly back to my broadband connection. Excellent device and great value for what it does. I can't recommend this highly enough for what it does. (see photo)

Good little unit, being used as a wifi bridge to connect an HP printer with only ethernet connection, which is not easily accessible to the network in our new house. The documentation for the unit is a bit sketchy, but I managed to get it working with the wizard and a few tweaks / tries to connect. Once working seems solid and provides a decent connection for the purpose.

Very poor - after an hour couldn't get it to work properly and I am experienced in networking. Instructions are a very poor translation and on some points do not match behaviour. Runs really hot when not even doing anything (because it wasn't connecting anything. Avoid this product. Also constructions and casing feels extremely cheap and I doubt even if it worked at all that it would last very long.

It's slightly fiddly to set up, and the speeds aren't great. But it does fix a problem where a single device has Ethernet but no Wi-Fi

Needed to enable Echo on University WiFi - works straight away - no messing

I had a Sky+ box and smart TV, each connected to a separate power link Ethernet cable - the Sky box is old tech and requires a "wired" connection and the TV has terrible builtin WiFi, and the power link devices suffer from poor electrical wiring in that part of the house so they are also rubbish. This device comes with less than obvious instructions, but here is what worked for me... It can be configured in all sorts of ways, but what I needed was the Bridge/Repeater mode configuration. This is fairly easy - plug both the Ethernet and USB (for power) cables into a computer then open a browser pointing at 192.168.253.254 and enter userid/password as admin/admin then select the Operating Mode tab and change from Router to WiFi Bridge + Signal Repeater mode, click Apply then Reboot. When it comes back login again and it should should show wireless connections, select your own router then click Next and supply the router password (as in the one printed on the back of the actual router). It then requires that you press Reboot and this is where the instructions get vague... the lights on the unit will start to flash, indicating all is well, but your browser page will never refresh. Don't worry - its good to go now. I then plugged the USB and Ethernet cables into the Sky box, thereby fooling it that it had a wired connection and reconfigured the TV to use the "new router" which is the same as the old router name plus an additional suffix. The signal from this device is awesome and both Sky box and TV now have great internet connections.

Bought this mini router as a cheap WiFi to Ethernet bridge to get a Windows 10 PC without a WiFi adapter into a Hotel wireless broadband. Had to use my laptop to configure it, find the admin credentials in the (tiny print) manual, and select the right options from the extensive screens. Once successfully connected to the WAN, it works flawlessly and reliably, too much blinking, would be nice to reduce the LED usage sometimes. The form factor is minimal, much smaller than I expected but cable length sufficient to connect to a back pane. There are Wizards for most functionality usually to be found only in more expensive routers. A decent piece of hardware well worth the price.

Had a solar camera that can't store to my NAS. Wanted to use another PoE camera I had without needing to run ethernet. Setup wasn't too bad, connect to computer via ethernet, go to URL, set mode to bridge, enter WiFi creds apply and reboot. A minute later the camera was up and running. Hopefully in relation to what others have mentioned, heat issues won't plague this setup.

My Beringer X-air 12 mixer has a very inadequate WiFi that let massive interference when there was a lot of WiFi going on. This item cured the problem and haven't had a problem since. Five stars ⭐⭐⭐⭐⭐

使いやすい

Flashing led Lights are too bright and are not usable for astro imaging. Have painted top of container with Black permanent marker to try to reduce light. If I used electrical tape that would inhibit natural cooling that is if it generates any heat? A star/nebula could take 0hrs to 3+ hrs to image. Smaller led's Any other ideas to also reduce power consumption to decrease battery drainage. Daylight shooting a big 5 stars. ***** Night Astronomy With led brightness greatly reduced 5 Stars ***** Modem is small and light, Connecting leads are a good length for Aisair plus. Anyway to fix led intensity suggestions would be great appreciated.

piccolo e performante, funziona alla perfezione ed è stato semplicissimo da configurare, io l ho utilizzato soltanto come client wifi per un dispositivo che aveva solo presa lan e non volevo vincoli con il cavo di rete. l'interfaccia di configurazione è molto intuitiva e comunque c'è un esauriente procedura guidata in caso si fosse davvero "pigri" - acquisto raccomandato

Très bien !