Diablo Steel Demon Cermet II Saw Blade with Triple Chip Grind and Perma-Shield Coating - Ideal for Medium Metal Cutting - 7-1/4" Diameter, 48 TCG Teeth - D0748CF

The Diablo D0748CF STEEL DEMON is a top-tier metal cutting blade that delivers on all fronts. It cuts through steel and stainless steel effortlessly, producing smooth, burr-free edges with minimal heat and sparking. The CERMET II carbide teeth offer serious durability—I’ve made dozens of cuts, and it’s still sharp and consistent. What really stands out is the functionality. Whether I’m cutting angle iron, conduit, or stainless tubing, this blade handles it all with precision and control. It’s versatile, dependable, and performs consistently across a range of materials and thicknesses. The 7-1/4” size fits my circular saw perfectly, and the 48-tooth configuration strikes a great balance between speed and clean cuts. It also runs cool and quiet, which makes the whole cutting process safer and more comfortable. Plus, the long life claim (up to 5X longer) is proving to be true in my experience—this blade is built for serious work. If you need a reliable, functional, and long-lasting metal blade, this is it. Highly recommended!

Ripping 4x8 sheets of 14ga galvanized steel, Sure it's noisy and tosses chips, but damn, this thing cuts right through it. I've cut through roughly 80' + of sheet, the top of my steel saw horses, tried it out on some 3/16" angle iron, Blade is still sharp and hardly shows any wear. Would definitely buy it again.

I mounted this on an old chop saw (miter saw), and it works wonders for cutting through metal. I've used it to cut through mild and stainless steel, up to 1/4 inch thick, and 6061 aluminum. I was surprised at how easily. Cutting through that 1/4 inch steel felt about the same as cutting through a pine 2x4. Quick and easy, with very little downward pressure on the handle during the cut. And the cuts are clean and smooth. My chop saw spins at 5000 RPM, and this diablo blade is rated at 5800, so it has been a good combination with no problems. Exceeding the max of 5800 may very well cause problems such as dulling the blade, so keep that in mind if your saw spins faster, and many do. While researching this blade, one reviewer commented that it is good for cutting through metal when the entire blade width is in contact with material. However, it is not good for shaving material off the end of a piece, as is commonly done to make a piece of wood just a little shorter. I can confirm that it's not good for this when cutting steel, as it creates a lot of vibration, and I was concerned that even a tightly retained piece could be sent flying. But for cuts down the middle of a metal piece, it's great. Since I'm too lazy to switch it out for a wood blade to make the occasional wood cut. I can confirm that it's a perfectly adequate wood saw. Not the best for making furniture grade cuts, but just take your time going through wood, and you get a clean enough edge for your rough cuts.

This is an excellent blade! It’s cut through a hundred rail road spikes and is still sharp!

It cuts fast and clean. I don't know yet how long it will last, but this blade is almost unbelievable in its capability and speed cutting mild steel. I'm using it on a worm drive SKIL HD77 saw which runs at 4400 RPM.

Cutting aluminum and stainless steel sheet with a circular saw may seem crazy but it works great. I have had the aluminum specific blade for a couple years and it is awesome for ripping aluminum sheet for boat projects. The Stainless Steel blade works "good" but not great. I noticed a big negative change in cutting performance over a relatively short period of time (only a few cuts) which means that cutting stainless material with a circular saw is going to get fairly expensive using this method. It still beats using a band saw as the cut can be made VERY straight on large pieces of material. It's a "good" blade but I don't think it's great for the $$ paid.

My gosh this a game changer, I've always used a torch or cutting disks, so far I've ripped 1/8 thick 7 foot long steel flat stock 4x and the blade is still cutting, why didn't I try this before 🤦

Great saw blade cut up to 14" steel with it. Cuts down on plasma consumables.

Perfecto me funcionó muy bien se ve de muy buena calidad

Beast

وصل المنتج بدون غلافة الاصلي

Great blade cuts perfectly just as advertised

Ótimo produto de qualidade é o que está descrito recomendo bom o acabamento de corte este e o segundo que comprei e compraria novamente