RH Adhesives Hh-66 Vinyl Cement, 4 oz Can. -

Muy buen pegamento, queda muy resistente

This is something that if you make any vinyl repairs to your pool is a must. It behaves a lot like PVC cement but it's not the same thing. I have noticed that many big box places will not have this on the shelf. Best way to use it is clean the area you are applying the patch, pre-cut the patch and then apply the glue liberally to one side of the patch. Don't put the glue on the liner. You can apply this underwater if you want. Do this before the sun hits the area to be patched, before the sun gets it hot or after the sun goes down. If you apply it to a patch and the surface is really hot, you will get poor results. One trick I've discovered this year is how to apply it better. I take a regular old dinner plate, lay the pre-cut patch on it flat and coat it with the glue. This works very well at getting an even coat and the patch doesn't stick or get dirty. And, you have a firm flat surface to apply the glue brush. The last thing you want to have happen is to hold the patch in your hand, try to coat it with this glue and drop it on the ground. You've ruined your patch and used up some glue. Once applying it, it depends on where you're putting it, but if above the waterline, I like to put a clamp over it for a while to make sure it sets the way I want it. Or you can sometimes hold a board or something rigid behind it to press it firmly. When it sets, it's not going anywhere. If it's under the waterline, some people fold it over until they're right at the spot to put the patch. You can put this underwater. Above or below, the real secret to getting a good adhesion is taking a plastic spatula and smoothing it out to get the air bubbles out. If you have a pool that has an inflatable ring that a cat or other animal has clawed, this will patch it but it's really not worth the time to try to do and come back later to see if it'll hold air. this is more designed to hold water back than it is to hold air in. I let it cure for a 24 hour period, came back with soapy water in a squirt bottle to test it. Some patches held and others had one leak making it very difficult try a second time. I finally decided to go another route. The best way to fix that is cut a slit(s) on the outer part of the ring away from the waterline just big enough for an empty two-liter soda bottle (with cap on) to slip in. You may want to make around four slits around the pool and insert these empty soda bottles. You want to pack them in but not so tight that it stretches the ring. If you stretch it taut, the sun will crack the vinyl. After getting the soda bottles the way you want, cutting a strip of a vinyl patch and using this glue will solve your problem. I've never had any problem with this method and it holds up the pool, keeping the water in. You can add the noodles inside with the soda bottles and it'll work just fine. The sun will not degrade either inside the ring. The sun will degrade a noodle left in the pool but not the plastic soda bottle. One can is likely going to be enough to last you for your needs. But, like PVC cement, don't expect the unused portion to still be liquid the next season. So, use it liberally. This is the best type of glue for vinyl pool patches that I've found. Now that you have the best glue, pair that with quality patches. Cheaper, thin patches will pucker up with this glue and you will get poor results. One thought on the patches, pre-make your patches so that you can apply them one right after the other. Match it to the hole and make it bigger. You can center the patch area on the liner and mark it very lightly with a felt marker, just enough so that you know where it goes. When you make your patches, always make them rounded. Don't make corners that can catch on something. The goal is to get the glue on the patch and vinyl liner but not coating the patch with glue on the edges outside the patch. To clean the vinyl liner, soapy water will work followed by rubbing alcohol or just rubbing alcohol. Any stronger chemical I would would do a test patch as it could dissolve the patch or liner. If it starts to get gummy, you don't want to apply that cleaner on either the patch or liner.

Excelente pegamento para usar en mi Paddle Board inflable. Es un poco caro pero fue la mejor solución!

Ya llegó el producto y todo perfecto

I left it alone to set, and later that evening the footrest held air again. My kids were back to using it while watching a movie, and I was glad I had the glue on hand rather than having to replace the whole thing. The repair stayed flexible when we moved the footrest around, and I like that the dried glue didn’t leave an obvious mark. The 4 oz tube gives me enough for more than one little fix, so I’m keeping it with the household repair stuff. I’d use it again for a vinyl tear or a small patch job. Just take a minute to prep the surface and let the repair sit before putting it back to work.