Single Monitor Arm Desk Mount for 17-49 Inch Monitors, Black | Heavy Duty Monitor Mount Stacked Monitor Arm Desk Holds 44 lbs

Ater trying numerous monitor arms, these are my go to unless there's something specific needed (longer arms, additinoal neck rotation, wall tight against back of desk). The Ares Wing is very clean looking, yet incredibly stable. It has tight tolerances at every connection from the post and base, to teach of the elbow joints. The quick disconnect monitor plates make iit very quick to swap monitors around. I also like how simple and effective the tooless cable management is. I've used AVLT, Ergotron, Ergounion, and numerous lesser quality brand mounts. These are superior in fit, finish, and simplicity. The caviat is I'm currently using the base from this mount with AVLT arms as I wanted a little bit more range of motion with the longer arms and my 34" widescreen monitors. I do however like how these look better and they are a much better value.

I have one other monitor mount with a different design that does not allow for height adjustment anywhere close to this level. The pneumatic arm has become loose over time, down at the base where it attaches to the mount, making it virtually unusable for anything above 8 inches from the desk. I found this far superior design and ordered it to use with a 34 inch wide screen monitor and it performs even better than I expected. The design is as good if not better than any other monitor amount I have seen of this style or several other styles, and I highly recommend this product to anyone with a monitor within the quoted weight range. I will actually be ordering another one of these to mount my other monitor so I can have my main monitor at the height. I prefer in my slightly smaller and secondary monitor mounted above that. Right now, the other monitor arm mount that I purchased is forcing me to run my primary monitor above my secondary monitor. It’s actually not a problem with this due to the amazing adjustability of this product and the fact that I can easily tilt my upper monitor downward and set that angle by tightening a screw on the “swivel.” I will include a couple pictures to show exactly what I just described which I hope help people make their decision on whether or not this product is correct for them. Hope this helps! ***EDIT*** I was sent an email with a question about how well the pneumatic arm and tilt function works and holds the monitor where you want it to be. This monitor mount is the ONLY mount I have found that will hold a VERY heavy monitor, (within the specs of whatever is listed,) to actually hold that weight in place precisely where you want it, but also be able to adjust without a massive headache. There are a couple of different set-screws which adjust the tension on the swivel mount, and also the height mount, which allow for you to make it easier to adjust, or for a lighter monitor. I set the screws fairly tight, so my monitor holds in place precisely where I want it to be since it is a 34 widescreen model, and a little north of the halfway mark for the weight limits. I don't remember the pound limit off the top of my head, but when ordering this product I remember that what I have was a little north of halfway. I think my monitor is something like 20 pounds or so. This mount will clearly hold something twice that heavy, with ease. I truly cant recommend this product enough and will be buying another one fairly soon for a third monitor I am purchasing. Hope this helps the man who asked the question, since I cant find the email to respond to his question anymore. Cheers!

I’ve been using this dual monitor stand for about one weeks now, and so far, I’m really pleased with it. I bought it to replace the stock stand on my G9 because the original stand took up a huge portion of my desk. This mount helps free up all that space underneath, giving me a much cleaner setup. In the future, I plan to add a second 49” monitor, but for now, I’m using it to hold a 32” monitor above my G9. Once set up, the stand has been rock solid. Assembly was pretty straightforward, though I had to estimate the right height for the lower arm before securing it. I also positioned the upper arm at its highest setting. Attaching the monitor to the mounting plate took a bit of effort—especially with a display of this size—but that’s to be expected. Having a second person to help definitely makes the process easier. One thing I noticed is that if your monitor tilts forward after mounting, the best solution is to hold the monitor at the angle you want and gradually tighten the bolt in the wrist joint until it stays in place. This seems to be a common issue with mounts for 49” ultrawide monitors, as I’ve seen similar feedback on other models. However, it’s just a one-time adjustment during setup, so it’s not a dealbreaker for me. Overall, this mount offers great value for the price. Unless you’re willing to spend $300-400+ on an Ergotron, this is probably one of the best options out there.

A very high quality product. From packaging to final use, there is nothing to complain about. Highly recommended. I didn’t ever move my monitor on its original stand, but after installing the arm, it is so easy to move aside that it don’t even think twice. I will never use the factory monitor stand again.

I'm deducting one star because the cable management channels on the underside of the arms are held on by fragile plastic clips that require some force to engage and only slightly more force to break. Be gentle; I've broken two of them. So far it seems like excellent value for the money overall, though. The arms are solidly built out of sturdy metal, they articulate smoothly across a wide range of motion, and they have thus far held the one monitor I currently have attached to them with rock-solid stability.

Thank you to all the feedback and reviews others have left first if all. This stand is great and works very well! It's very strudy, tilts well and the instructions, while very minimal and wordless, did a great job of getting everything set up. The movement is sturdy and easy. Since my monitor was so large, you will need some assistance with making sure it snaps on to the mount correctly. It's not a one man/woman job with large monitors. The one up top was simple. I will say, please watch the instructions on how to tighten each arm as they aren't like mechanical arms where they just drop for adjustment quickly, they will hold but they'll move in different directions based on what your arm is doing. I did read that you can break the arms by over tightening, so please be careful. I didn't have this issue, as they are heavy and solid arms. I DO WISH - that they came with a longer pole base from the start. 45 + 34 is really pushing it as far as getting them to be firmly seated, but they're really close together as you see by the photos. The smaller pole base just doesn't allow enough height but it does work and still looks great. You'll find a balance.

If you want to pay for an expensive mount just to have an installation nightmare... be my guest. I somehow ended up getting it to work in the end, but only because I improvised. I could tell that the item I got was not new and in fact returned due to the arm that positions your monitor's tightening screw being stripped. I've never run into this with an allen wrench install before. It's because the one they provide is rounded and too loose a fit. If you want the install to work, use your own. The instructions actually have a warning that tell you not to tighten it too tight, with no mention of what the consequences are. Let me tell you those consequences... you will BREAK IT. Both of the arms have hydraulics in them... so if you break this part (which at this point you probably have a REALLY high chance of getting one that's already broken since Amazon states this is a frequently returned item), you will be left with a mount that can not be adjusted vertically, and it will just stay propped towards the highest position. I spent an ungodly amount of time inadvertently working out my arms just because I had to push the hydraulics down to allen wrench a screw that was doing absolutely nothing no matter which way I turned it. The way I worked around it was by putting the broken one on top, since the top position doesn't really need to move lower. The hydraulics were a good idea, but the implementation of the tightening and the extremely cheap tools provided for installation made what should have been a super easy install into a nightmare. If you got to the same steps I did and decided to return this, it would have been way worse because you would have had everything pretty much done just to take it apart... and if you took your monitors down already and prepped the mounts... it would just be a big waste of time and energy. So that's why I kept it, to maintain my sanity. But save yourself the trouble and buy just about any other mount because they are rarely this bad.

I used the ARES WING Dual Monitor Arm Desk Mount for my custom gaming desk build, and it absolutely delivered. The setup turned out amazing—this mount really elevated the whole look and feel of the space. Installation was straightforward, and once everything was in place, the arms felt incredibly sturdy. I’m running larger monitors, and it holds them without any sagging, wobble, or adjustment issues. Everything stays exactly where I set it, even after long sessions. Beyond stability, it also helped free up a ton of desk space and made cable management much cleaner. If you’re building or upgrading a gaming or work setup, this is a fantastic choice that combines strength, flexibility, and a sleek design. Highly recommended!

J’utilise ce support double écran tous les jours au bureau et honnêtement, je n’ai absolument rien à lui reprocher. La qualité de fabrication est excellente : les matériaux sont solides, les articulations sont fermes et le maintien des écrans est parfaitement stable, même avec des écrans de bonne taille. L’installation a été simple et rapide, avec des instructions claires et tout le nécessaire inclus. Une fois en place, les ajustements sont fluides et permettent d’obtenir une position de travail ergonomique optimale, que ce soit en hauteur, en profondeur ou en angle. Ce que j’apprécie particulièrement, c’est la stabilité dans le temps. Contrairement à certains supports plus économiques, celui-ci ne s’affaisse pas et garde ses réglages, même après une utilisation quotidienne intensive. Résultat : un espace de travail beaucoup plus propre, mieux organisé et surtout plus confortable. C’est clairement un excellent investissement pour toute personne qui travaille plusieurs heures devant écran.

Easy to set up, we'll built and adaptable to different surfaces. It works perfectly and I love its wide range of flexibility.

J'étais retissant d'acheter cette article vu le prix mais j'ai quand meme passé a l'achat et pour etre honnête je suis très satisfait. Robuste et rassurant! Je donne 4 étoiles sur 5 vu que je l'ai depuis seulement 3 semaines et je me garde une gêne mais pour l'instant rien a dire.

I bought this mount for my 43-inch monitor and was a bit skeptical about whether it could handle the weight, but it’s actually pretty solid and holds up well. One downside: the plastic cable holder was broken out of the box. I ended up gluing it back since it didn’t seem worth the hassle of returning the whole thing for such a small issue. Overall, the mount does its job and feels sturdy where it matters

Excellent! Was pretty simple to install. Since I have a pretty large monitor you have to make sure that the base and clamp aligns with wherever your monitor sits in the middle of your desk. Otherwise you would need to take off the monitor, put it back on and make adjustments.. Otherwise great product! Definitely a huge upgrade going from the monitor stand which took 50% of my desk depth. Very sturdy and offers great movement.