Question 1

just got the guided field sharpner no how do you use it

Accepted Answer

With the edge facing away from you, push the blade down the diamond plate (the grey part). There are two diamond plates, one is coarse and the other is fine- running your finger down them will tell you which is which.  Use the yellow guides on the ends of the sharpener to tell you what angle to sharpen your blade at.  Maintain that angle the whole length of the plate as you slide the blade down it.  Don't press too hard, let the plate do the work.  If you press too hard you can roll the edge and make it harder to get a sharp edge quickly.  Run the blade over the plate about 10 times on each side and then check for sharpness.  Repeat until the edge is where you want it.  Once you're happy, use the ceramic rod (there are three sides-smooth, ridged, and the fish hook sharpener) and run the blade- at the same angle you used to sharpen it, down the ceramic on alternating strokes until the edge is as sharp as you think you can get it.  The leather strop works a little bit, but if you want a cheap strop to put a shaving edge on your blade just take a piece of cardboard and rub in some regular metal polish and let it dry.  The cardboard has lots of silicate in it from the manufacturing process and with the polish it acts like a 3000 grit strop to put a fine polish on your cutting edge. The finer the polish, the more like a razor it becomes.Hope this helps.

Question 2

What are the different grit numbers for each sharpening and honing service?

Accepted Answer

The coarse grit diamond plate on the Work Sharp Guided Field Sharpener is 220-grit and the fine diamond plate is 600-grit. The ceramic honing rod is not measured in the same way as the diamond plates, but according to our engineers it would be between a 1000 and 2000 grit. The only difference between the coarse and fine sections of the ceramic rod are the ridges, which reduce surface area to increase surface pressure and acts as a coarser surface.

Question 3

How hard would it be to sharpen a 7 inch blade on this? I was going to buy the sypderco sharpmaker, but after seeing this I'm not so sure.

Accepted Answer

I watched my buddy sharpen a fillet knike with it using sweeping angles and it worked fine. This when processing my deer so we had to sharpen it "tons" of time. I believe the knife was a 7" blade.

Question 4

Are there other plates available for this tool other than those that are supplied. i have the wsgss that has an accessories kit that has other plates.

Accepted Answer

There are no other diamond plates available for this model sharpener. The WS Guided Field Sharpener uses a Coarse Diamond Plate, 220 grit and a Fine Diamond Plate, 600 Grit. The ceramic rods may be used for a finer blade edge and then honed using the attached leather strop.

ASIN	B009YKHZ96
Best Sellers Rank	#1,361 in Kitchen & Dining ( See Top 100 in Kitchen & Dining ) #8 in Knife Sharpeners
Brand Name	WORK SHARP
Color	Black
Customer Reviews	4.8 4.8 out of 5 stars (12,754)
Global Trade Identification Number	00662949038751, 00788857026472
Grit Type	Coarse, Fine
Included Components	WSGFS221
Item Dimensions L x W x H	9.53"L x 5.42"W x 1.12"H
Item Type Name	Tool/knife Sharpener
Item Weight	135 g
Manufacturer	Work Sharp
Manufacturer Part Number	WSGFS221
Manufacturer Warranty Description	Limited Lifetime Warranty covers defects due to workmanship and design, excluding abrasives. Warranty covers consumer use only, not industrial or commercial use.
Material Type	Diamond and Ceramic Sharpener
Model Number	WSGFS221
Number of Items	1
Number of Packs	1
UPC	637825891348 744288114508 797936431441 787388429202 740528467823 043903198016 635341675541 013588033919 758710430975 788857026472 799154403286 043945291959 753956961306 756655462358 015913821314 662949038751 751738416259 798762674835
Unit Count	1 Count

Guided Field Sharpener, Hunting and Fishing Knife Sharpener

Details

Details

Description

Specifications

Common Questions