Otter Wax Heat-Activated Fabric Dressing | 1 Pint | Meltable Waterproofing Treatment for Waxed Canvas Jackets & Rain Gear | All-Natural & PFAS-Free Beeswax Protectant | Made in Portland USA

I used Barbour wax initially and then tried this Otter..I like both and in my opinion they differ. I did a light weight 100% cotton field jacket with the Barbour and it turned out great, very supple and soft unlike a Filson tin clothe or similar but I probably could have coated it again to get more of a stiff finish..I did another 511 tactical heavy shirt with the Otter and the diff is it goes on thicker brushed and has a lot more of a thick coating before the heat process to impreganate it into the clothe..Another great way to apply it is heat the wax by sticking the heat gun on high right into the top of the can and when it melts a little stick the brush in and paint it on the garment spreading it as you use the heat gun and brush as you wipe off the excess before it dries which is much quicker than putting it all on the stove to melt it completely before applying..When I was finished both gave me excellent results with the Otter somewhat stiffer similar to a Filson finish..I find using a old iron to get this Into the clothe is best on easy to iron clothe then clean up any other spots with a heat gun or hair dryer just don't over do it or it will travel right thorough the clothe to the surface its on..This is a excellent procedure for both..My results were great and it was my first time. I think I'll stick with the Otter for price as you get twice the amount for the same cost and you will use the same per garment. Although the Barbour is easier and melts quicker and is more supple as you will have a hard time to know if the garment is Borboured by its looks and feel as it is soft but waterproof not stiff like Otter..Both are good though and if you don't screw it up you should be satisfied with either, but understand there is a reason you pay the $400 + cost for waxed jackets because they are a choir to do and you are paying for it so save and spend a coupler hours to save a couple hundred and do it to whatever you need to do it to..Up date; the garment I did is super water proof but it really smells and it smells everything else up in the storage. When I hang it in the garage, as soon as I enter it I can smell it a mile away..From now on only hunting clothes..

You have enough time with a brush to get the wax on to the garment, and a little spreading, but it will harden fairly quickly. A few pointers, warm the garment (about 10 minutes in the dryer), use a heat gun (this will be better than a hairdryer), keep the area you are working on, warm, wiht the heat gun. Keep the brush warm with the heat gun. Spread and spread and spread. Use your hands (they'll wash right up with Dawn dish detergent), spread and spread. Use the heat gun and get as much of the wax in the garment as possible. Stand back and say - "WOW, that looks like crap!" Now, put it in the dryer for about 30 minutes. (be sure to dry a load or two of towels after this). Now - stand back and admire your work. It will come out great. Just spreading the wax on the garment is going to take a good 90 minutes, probably more. Trying to get the wax to soak in with a heat gun will take forever. Drying it in the dryer for 30 minutes - that takes about 30 minutes and really spreads the wax out nice and even. The garment I did (a surplus OD Green field jacket) took the wax pretty well, but it was still too thick. I dried it for about 15 minutes, then turned everything inside out, did another 15 minutes and it looks great.

Works great but really hard to use. I needed to waterproof a canvas watercolor field bag. I found the perfect one on Amazon for around $40. The trouble is, the cavas was not water resistant at all. The quality and price of the bag were too good to pass on, so I decided to try and waterproof it with this product. It takes forever for the wax to melt…and, then, it goes from milky to clear before you should even think about applying it. I used a stiff 1-1/2” wide paint brush with stiff bristles. I could get, maybe, a 3” section of the bag sort of done and then had to put the brush back in the can to remelt everything and get the wax compound hot enough to go clear again. In any event, the bag tool four hours and looked awful, with missed sections and chunks of unabsorbed wax everywhere. So, the next day, I started rubbing tiny sections with my thumb and fingers. That actually works. As friction heats up the wax, the canvas absorbs it better and you start getting a uniform look….But life isn’t long enough to complete a backpack by that method, so I got out my heat gun. 90 minutes and I had a gorgeous, water proof, waxed canvas watercolor field bag. It’s been a week, now, and I would do this again…..but do yourself a favor and buy or borrow a good heat gun. Use it on low, to where it melts any bits of wax and the canvas absorbs them instantly. Fill in with the wax you scraped off with your wood tool (I used popsicle stick) when first applying the melted wax. Just kind stick it where you want it and melt it into the canvas with the heat gun.

After melting 3 cans and trying to paint and scrape and rub this wax on to a canvas tent roof, I started to question my life choices that brought be to this point in my life. Then I noticed a missed spot and took a chunk of hard wax from an empty can and rubbed it on. It worked great. That’s when I came up with the idea to just make my own “rub” bars from the cans. I heated up 4 cans and poured them in to 3oz soap molds making 24 bars. On a 55°f day in direct sun the fabric is hot enough to melt and set the wax, just with less mess and I’m also able to more precisely apply it to needed locations. I like this wax and it definitely waterproofed the fabric. The smell is also pleasant and not harsh whatsoever. However you choose to apply this wax, I highly recommend it!

Worked better than the Bar for me. I wanted to wax a chore coat I hadn't been wearing much for inclement weather. I tried using the Bar version of this, and it didn't cover the fabric very well. This stuff, once it finally melted on the stove, I applied it with a cheap chip style paint brush. I used the whole can, and ran a little short, scraped some off the coat, to re-melt and kept going. The coat was very waxy afterwards. A day or so later it wasn't drying as I'd hoped and remained tacky/slimy. I went over it with a heat gun, and could watch the wax seep into all the pores and seams. That did the trick for the expected outer feel of the wax. I wore it a bit to get the wax broken in, and knock off any excess. Overall it did not come out looking as I'd hoped, but I'm pretty sure the rain and snow will slide right off. I do wish they gave you a little more in the can. 1 can was worth the experiment, 2 cans was more of an investment than I was willing to put in.

Yeah it's fine. Nothing special. Very small can. It's just Beeswax and parafinwax way cheaper to buy those two and mix yourself. These guys are way overcharging. If you buy this can make sure you buy more than what you think you need. So far my 3xl Legendary whitetail Journeyman jacket has taken a full 1.5 pint and counting. My coating is full saturatation with excess being wiped and moved to a less coated area.. The coating does work. You can pour water and let it sit and it won't sleep through if laid flat on a table so if your are standing the water will absolutely bead off and fall into the ground. No smell. Little stiff. Dark matte color. Durability is that of wax, it's gonna come off eventually. Go mix your own 50%beeswax/50% parafinwax

Used on brush pants. Great dressing. Works as it should.

I used this to wax a brand new lighter weight inexpensive solid matte black coloured cotton jacket. I was hoping for water resistance and a nice even subtle silky black appearance maybe something like a Barbour though if it looked more like a Filson that would be fine too. Took a while for me to get the wax melted in the pot of water, probably would have been better on a gas stove, rather than electric, as the heat would have been even that way. Used a meat thermometer that I held with the probe off the bottom of the pot to ensure proper 180 degree water temperature. I applied the wax from the can still in the pot being heated on the stove to the coat a foot or so away with a new paint brush. It solidifies quick. I was rushing things a little and just quickly slopped on the wax to cover everything. the entire coat took the full can, though no more. I let it rest a few minutes then got out the hair dryer and used it to melt the wax until it was soft and then worked it in with a wooden shim that I had sanded down and rounded off. Made sure to work the wax into the seams, pocket pleats, and moved it around from areas that had been more heavily coated to those that were less heavily coated. Had lots of crumbs of wax that had blown off stuck to the side of the coat that was down on the tarp last. Flipped the tarp over, put the coat back down and began to melt the wax on the coat again and as I did I thoroughly and spread it around with a wad of old freshly laundered cotton T shirt. Certain areas like the top pocket covers looked good, like I was hoping the whole coat would turn out. Even the fabric on the chest above this looked like that, at the time. Did the whole coat like this. Beginning to end took about 4.5 hours. Then I hung it up to cure and let it set there for 72 hours. Only after that did I put it on. As soon as the fabric flexes it gets pretty chalky looking. Again the material above the top pocket flaps looked exactly like them and then that material flexed a little and turned a chalky grey. It's not the aesthetic I was going for and I'm not super happy with it, but OK it's not awful. My wife thinks it's awful, though, whetev. Stood out in the pouring rain with it today for 10 minutes. Watched the water sheet right off the whole time. I stayed completely dry. So it seems to have achieved the level of water resistance that I had hoped for. That is great! Very satisfied there. I'm thinking the aesthetic I desired is achievable, though I probably should have taken more time and watched the companies instructional video once or twice more as I was doing it. Also not having a needy 4 yo and 9 month old in my immediate care while I was doing it probably would have helped a lot. I'm guessing I over applied the wax and should have taken time to work each paintbrush application into the fabric as I went rather than brushing the wax on everywhere quickly and then melting it in and moving it around. I probably could have used 3/4 can and achieved a more even factory looking finish. I'm not worried about this as the item functions and the wax will need to be touched up re-applied in a year or so at which time I'll have another chance to make it look more like what I had wanted. I may try the bar for that touch up. So long review, in the end i'm very satisfied and would recommend the product. All in, jacket and wax, I've spent $42 and have a fall/spring coat that is durable and usable with some character and that I'll change the appearance of in a year or two when re-waxing; I'm putting this one in the win column.

melts fine with a head gun, but it stinks, the smell becomes unbearable after a while and very hard to get rid of. Had to wash the clothes 3 times to totally get rid of the smell.

When warmed up, it’s easy to apply on fabric. 1 small tub can last about 1 extra large jacket.

Miniature. No where near a "half pint", not even half a cup. More like "100mL" (1/10 pint) I'd estimate. Bought this per reviews expecting a good product and importantly sufficient quantity to re-wax one jacket and other projects. That won't be possible due to deceptive and misleading advertising.--Full refund please.

A little difficult to work with but this is to be expected. Provides good waterproofing for oil skin outer wear.

Je déconseille