VADANIA Kitchen Cabinet Blind Corner Pullout Organizer for 36-inch/900mm Cabinet, 2-Tiers Swing Tray, Soft Close, Right Handed Open

I'm writing this review mainly because I saw some criticism of how this thing fits or doesn't fit, and if it fits standard units, and how poor the instructions are most of which I found to be completely untrue. It does fit standard units, and the instructions are quite adequate. The only wrinkle I found was the dimension given for the distance from the end of the cabinet to the hinge point (470mm, for a 1000 unit) wasn't possible with my centre post. But this measure should really be given as a range, say 470-something over 500mm. I was able to keep the shown distance to the front of the until and fitted it as close behind the centre post as possible. Note that fitting the top shaft fixing is always going to be quite awkward unless you are doing it with the worktop removed! consider that on a new installation! It all fits and works well. Quality seems extremely good. All the parts were there but some screws were lose in the box and not in the plastic bag. Note how these things are sold under a few different names, and they play a game with purchase price and shipping that makes total price very similar whichever you buy.

A good, well made and sturdy product, but the assembly instructions are simply a series of drawings which are it very difficult to determine relevant measurements. Also, I found that by trying to follow the flow diagram of instructions just made it far more complex and inaccurate. I installed the right hand pole, and arms first rather than the left hand bracket (assuming a left hand opening cabinet). The critical measurement for the pole, is 4850mm from the left hand side of the cabinet, and then 50mm in from the outside edge, both for the bottom and the top fitting. These measurements are where the centre screw should be located. Once this pole is secure, temporarily attach support arms to the left hand bracket, and adjust the whole assembly so that both sets of arms are level with each other. Now mark off the height from the bottom of the cabinet where the bracket should meet and secure the bracket to the left side of the cabinet. Once this is secure, it is then simply matter of attaching the trays to the two sets of swinging arms.

Its a nice looking unit, bit overpriced in my opinion but that seems to be the going rate for these things. Makes use of a cupboard, measurements were all correct and took a novice not too long to install.

Exactly what we needed to make best use of our blind cupboard. Easy to install once I realised that the position for the notch on the bottom bracket for the shaft didn’t matter (if you’re buying this that’s good to know!). Took about me an hour to install on my own. Seems very sturdy and I think good value for money.

SUMMARY: DON'T BUY IT, IT'S NOT WORTH IT -> It's a poor-quality product. -> Assembly instructions are very confusing. -> Instead of helping you make use of your blind corner space, it makes it almost unusable. -> If you really insist on a pull-out solution, do yourself a favour and go to B&Q instead. You'll save yourself a lot of time and stress. You can thank me later FULL STORY: A little context first. I installed a blind corner kitchen cabinet from B&Q recently. We have a small kitchen, so I wanted to use that space efficiently and also avoid getting on all 4s every time I need that deep pot. I saw the Pebre pull out system in B&Q and I loved the idea. Unfortunately, I am cheap and stupid, so I found this Vadania product and decided to save some money... The problems started right after unpacking. The assembly instructions are very confusing. It's relatively obvious how to install the pole on the left-hand side but good luck trying to figure out the right place to attach the panel on the right-hand side... I found the manufacturer's video on YouTube, but the measurements for the placement of the panel were different between the video and the instructions included in my package! After I finally figured out how to install all the arms, I tried to place the shelves on them. No luck! One of the bolts went into the bearing quite smoothly, but the other one wouldn't go in at all. I thought I was doing something wrong, maybe not aligning or not leveling the shelf correctly. So I removed the arm and tried to place it on the bolt while the shelf was upside down, so I can see everything and align it correctly. Still no luck! I've put some pressure on it, the bolt went into the bearing a little bit and got stuck! FFS... The bolts on the second shelf were better so I managed to install that one. I decided to see how it works before trying to install the first shelf again. Here comes another issue... I realized that the shelf is super small, which combined with its awkward shape makes it pretty much unusable. It's not even big enough to put a dinner plate on it, let alone a couple of frying pans. I mean, you can put them ON the shelf, but they don't below the rails... FFS! The bottom line is that while trying to save 100 quid I wasted 200... The shelves are completely useless. I have thrown them away and installed a normal shelf. It's less convenient to access but now I can actually use the cabinet space efficiently. The pull-out system sold in B&Q seems to be better. The shelves don't have high rails so it should be easier to place items that don't fully fit within the shape of the shelf. However, I'll stay with a normal shelf for now.

I was a little bit skeptical of these as they seem to be about half the price of similar units available elsewhere, however I needn't have worried. The units are solid and have a smooth action, they self-close without any issue and fit a decent amount of stuff on them - not as much as standard shelves but enough to feel like you are getting a net benefit from not having unusable space at the back of the shelf. I can't vouch for how easy they are to assemble as my kitchen fitter assembled them for me... badly! Upon assembly the shelves were wobbly and wonky but that was an installation error rather than a product fault... maybe the instructions for assembly aren't great - It was obvious where the kitchen fitter had gone wrong and I was able to correct his errors within 30 minutes, after which i now have rock solid shelves that I am fully happy with.

A little over priced considering the size but installed well and makes life easier. Opens up access to a corner unit in my kitchen. Was going to get one for the opposite cabinet but it is quite small. That being said you can stack 2-3 saucepans high and some smaller items.

The unit is solid and feels well made. It works smoothly. My only issue is with the instructions. When is says you must install the upright pole 485mm from the left wall of the cupboard, it means a MINIMUM of 485mm. At first I thought it had to be exactly 485mm, meaning the pole would be the wrong side of the cupboard upright. Once I figured that out (after drilling unnecessary holes) it was smooth sailing.