- Eagle Klaw 2.0 Floor Mat Clips (4 Sets) for Car Mats and Floor Liners - Made in USA Car Accessories - Black - 2 Car Floor Mats kit Without Cutter

I have an older car that is in very good condition except the front driver's floor mat would constantly slide. It also had some wear where the clutch and brake area. Being that it is a standard, it would slip under the clutch and it would cause issues especially when starting. If the clutch is not fully pressed, then the car will not start. Recently, I had to go into the bowels of valet parking because the attendant couldn't get my car started at the local casino. :) This prompted my research for an answer.Firstly, I bought another product that covered the wear and tear area with a hard plastic protector. This resolved the wear and tear issue. Lastly, I bought this product. You simply drill holes in the existing mat and follow the instructions. I did see where people were complaining about the final step of using a hammer or feet to secure the mat. I used a hammer without issue. Advice - I would not buy the hole punch option. Just use a drill, it will work and save you a couple of dollars.Overall - This is a GREAT product and highly recommended. It solved a long time problem for me.

Weathertech front seat matts that would not stay in place. Bought this but found really wants thick caroet. Got installed on Wealthertech and so far so good.

There are solutions to the “moving floor mat” problem that anyone can do cheaply with a few items from a hardware store. What makes this product nice is that it’s an easy, no fuss, single item purchase, that solves the problem. What more could anyone want? Well...it turns out that this product is genius in its design, but it falls short in execution. The design is great, but the plastic used to make the product is low quality, and brittle.I found that these fastener/claws, broke during install, 50% of the time. I’m glad that I bought more than I thought I would need, and I ended up using all of them. Twice the anticipated quantity needed.The plastic is brittle... but what also contributed to the plastic breaking was that the car floor has only a minimal amount of carpet thickness and padding. When using a hammer to strike the top of the claws to install them, they go fully through the carpet and pad, and hit the metal floor of the car.I have a Honda CR-V EXL. It’s top of the line Honda, but still a Honda. An Escalade or Mercedes May have thick enough padding so the claws don’t hit metal during install. But it’s likely the most common user of this item is a person with a widely sold car and not a specialty car. So most people are likely going to have minimal padding and thus are at risk of breaking the claws.Now for the good news. This product solves the problem. The product does work. I drive Uber and give 20-30 rides a day. EVERY TIME a rider got out, the carpet mats were shoved and crumpled up under the front seats and jammed under the center console. After EVERY TRIP, I had to reach behind the front seats, and straighten the mats for the next trip. I was going insane. I couldn’t figure out what the heck the riders were doing with their feet back there to create such a mess.I researched on the web for ways to keep the mats in place. I went to the dealership and auto parts stores, asking dozens of people in the car business and other Uber drivers, for feedback on how anyone else had solved this problem. No one had an answer. No one knew of a solution.The closest idea to a solution I could find was a DIY YouTube video by a guy who had crafted a solution using grommets, and self tapping screws yadda yadda. His solution was inexpensive. (a few dollars) and it clearly works. But it was kinda time consuming. It wasn’t quick and easy at all.Then by total luck, I stumbled upon this product. I bought it, I installed it, it works.I have had many many hundreds of riders since I installed these about 5 months ago. The mats stay exactly as placed, and many hundreds of feet, pushing and grinding as people got in and out, didn’t move the mats at all.More good news. The color grey of the product matches the factory carpet. Nice. They’re hardly noticeable. It seems that the brittle plastic is not an issue once installed. I feared that all the foot traffic, pushing on the mats over time, might break the plastic or the claws might gradually pull loose and need to be installed again. It turns out that my fears are unfounded. None of these concerns came true.Once installed, these claws are super performers in every way. Just make sure you buy twice as many as you think you’ll need because 50% may break during installation.NOTE: For my Honda CRV, there are 2 mats in the rear. They “mate” in the center, creating what asthetically appears as one continuous mat from left to right. I used THREE claws for EACH SIDE, for a total of SIX claws. I recommend a minimum of 3 claws per mat. I wouldn’t count on just 2 to hold properly. With only 2 claws per mat, each claw has to do too much work. Use a minimum of 3 per mat. Larger vehicles may be better with 4 per mat.

Does what it supposed to do. Really attaches itself to the carpet and makes any floor mat immovable.

Used in 68 mustang. Once you set them with a rubber mallet, they'll stay.

Use these to keep my factory all weather floor liners in place in my Ram 2500 tradesman with vinyl flooring. The mats would slide around badly with nothing to hold them in place. With these, the mats stay put just like they would on carpet. They are extremely easy to install as well. Just attach them to the mats, and gently hammer them down and you’re done!

****UpdateThe company reached out and sent a new set of anchors. Unfortunately, 3 of the 4 still broke at install. I didnt attempt the 4th as 1 anchor on the side is useless, if it would have actually worked.Used a pick to premake the holes in the floor of my truck, rubber mallet to tap into place, still broke the spurs and 2 of the arms on each anchor.Updating to 4 stars for the effort, product still not a fit for me or my vehicle. So I have holes in my $200.00 floor mats that still slide around as they did without the holes. Maybe Toyota just doesnt have enough backing for something like this to work. I could hear the spurs hitting metal and breaking as I was tapping them into place.**********Could be me, could be my vehicle, but these simply do not work. I tried the stomp method, they broke, I used a soft rubber mallet, they broke. I was able to salvage 2 of the 4 claws enough to finish the work, but they are both minus 2 arms and the nut does not secure into them.Maybe if they werent entirely plastic they would work better. Maybe like a thin metal arm with a polymer claw would work better.1 star because you cannot give 0 and 1 star for being American made. If they were $5 or $10 easily a 4 star product, but not at this pricepoint.

The product is easy to install and works well.

Installed 2 wks ago and very happy....car carpet doesn't move at all....they were easy to install,,much better than the Velcro attachment BMW provided

Does the job

Installed with my 3rd row passenger mats in my Pathfinder and it worked exactly as I expected.

Breaks easily. Probably for vehicles with thick carpet or underlay. Not good for Maxda5