JOYJOM Micro ATX Case PC Case: MATX Case Mini PC ITX Desktop Computer Case Support Micro ATX MATX DTX ITX Mini PC with USB3.0, support 3.5'' HDD (Black)

Usandola con una placa mATX, todo cabe bastante apretado. Olvídate de usar ventiladores de 25mm de grosor, incluso los de 15mm están apretados. Igual el pcb de los botones y los puertos estorba mucho para meter la placa. Con mucho cuidado y paciencia es posible.

This is a nice compact case ideally suited for the MATX motherboard. Given the motherboard has a CPU and PSU fan, as well as vents on the case, a case fan is unnecessary for everyday normal use. It comes with mounting screws attached to the cable with elastic bands.

Decent. Small. You get what you pay for. I needed a very tiny case for a tv gaming PC and this works well. Very happy with it overall. It is really tight getting everything in it and I used 3 fans.

I like the case. It takes a full size at power supply which is good for ryzen 7 5800x. But it's a hot processor and I first ordered 120mmx25 front fans and they didn't fit so I went with 2 noctuna NF-A12x15 for the front and they fit perfectly but don't squeeze the case on the front picking up the computer puts enough force that the front panel will touch the spinning fans. They could use washers behind them. just be careful to shut it down before you pick it up to move it and you'll be fine. The cpu cooler was 7/10 hard to install I first went with a smaller noctuna model number in the photos but replaced it with NH-C14S which is the absolute largest intel/am4/am5 cooler I could install. While tucking the wires to the side I can still add ram and replace the ssd with the cooler installed. I used a micro screwdriver to plug in the cpu fan because it was such a tight spot to get into. I used an extention first from the 120mm fans to help because the large cpu fan barely reached my motherboard plugin. I used a splitter for the two front 120mmx15mm noctuna fans and I put an 80mmx25mm noctuna fan on the back. The temps were at 70 and 80 degrees just running unraid and a single vm with smaller cpu cooler the large cooler keeps idle at 49 degrees c and 60-65 under heavy load running benchmarks which is just fine. This was a quick build but I had to experiment with which fans all fit the fans cost more than the box itself I spent $200 on cooling fans. If I did it again I'd pick a larger box that comes with fans already. But now that it's already together and running my surveillance system I'm glad it has a small footprint. Enjoy the photos they show which components fit to maximize cooling. I figured 550 was plenty for power supply 105watts for the 5800x and 100w gtx1030 was all I needed for a gpu to run code project ai and agent dvr with ai object detection. I picked up a 2 tb nvme xpg gammix I had laying around and the cpu came from my other server I recently on Amazon purchased ryzen 9 5950x. I wish I could afford to buy another it runs at 35 degrees when the 5800x runs hotter 50 degrees. overall the case is good it can hold all the cooling power u need with special fans and it's small takes up little room and has the basic no frills look I wanted. It holds 4 ssd 2.5inch and no 3.5 if you put the front fans in which you need for temps. So undecided if I want to order the corsair case and tear this down again and it has 2 3.5 bays plus 2.5 ssd storage and cable management. This case has poor cable management. Better off if I had gotten a modular power supply. But it was a bit over budget. You decide.

Great size, fit my B450 prime with an RX570. The mobo mount screws from my old case didn’t work, which took me a while to figure out because I didn’t notice they included mounting hardware. Since it doesn’t come with any fans I’d also recommend getting a few small fans as well just so your system doesn’t suffocate.