WEARSON Low Profile Monitor Stand - Foldable Touch Monitor MINI PC Stand Compatible with VESA 75x75 and 100x100mm Monitor Mounts For Kiosk,AIO Monitor Base Adjustable Folding Flat

I needed a small display stand for my portable monitor. My monitor is a bit larger and about as thick as an iPad Pro, and needed something that was also small and light. This stand is actually built very well, including the plastic parts, which seem to be of good quality and are pretty thick. The base and adjusting mechanisms are all made of metal with plastic covers. It actually was a bit heavier than I was expecting, but it was only due to my lack of scale when purchasing. I was thinking this was a bit smaller than what arrived, but I was not disappointed. There are a few reviews about how tight it is to adjust. This was my initial thought as well when I opened it up and tried to adjust the stand. it was TIGHT! I knew my super thin monitor would break if I attempted to adjust the monitor with it as tight as it was. I have no fear of taking even new things apart to best suit my needs, and I knew I could fix this by dismantling it. Most are built the same way with some sort of tension adjustments, usually just lock nuts. In doing so, I quickly discovered that this CAN easily be adjusted without taking the entire thing apart. It is actually designed so that users can adjust the tension with the proper tools, and minimal dismantling. You will need the following tools: * Philips head screw driver (#2 - most common) *10 mm box-end wrench (for upper Vesa mount adjustment) *13 mm box-end wrench. (for base mount adjustment) All that needs to be done is remove the four larger screws that are grouped close together in the bottom base, (where the neck attaches). The base will separate from the rest. Then just remove the one screw on the Vesa mounting plate in the very center, removing the plastic cover. If you have a monitor installed, you'll need to uninstall it to have access to the center screw. This exposes the lock nuts on each end of the neck that can be loosened or tightened as needed. A little bit of loosening goes a long way so adjust in small increments. Try to make the same loosening or tightening adjustments to each lock nut pair equally with each other. Lock nuts are designed to keep their position no matter how tight or loose, so there is no worry for those nuts becoming loose or tightening up later on. I have mine fine-tuned to my super light monitor and it adjusts with minimal physical input, but maintains its position where I need it.

I have updated my WiFi setup to WiFi 7. I purchased Ubiquiti’s E7 WiFi module for this purpose, but I wanted to have it as a desktop setup instead of wall or ceiling mounted option. Since the E7 is 75mm VESA compl, I purchased Wearson’s low profile monitor mount. It works perfectly and fits well with my intended setup. Highly recommended!

It works great with the 1010music bento. I can finger drum on the pads and the stand doesn’t give or slide on my desk. I took off one star because the included spacers have too big a diameter to work with the vesa mount holes on the device. But I had some short Eurorack screws on hand and they fit great.

So hard to choose from cheaper ones more expensive ones some that cost five times as much however, this does everything it said plus more looks great sturdy not cheap and let me tell you they could probably charge twice the amount and sell this

I own a Flex Maestro controller for my Amateur Radio transceiver. It has a VESA pattern on the back, but comes with a crappy sheet metal stand. This VESA mount fits PERFECTLY on the device and is infinitely more flexible than both the cheap bent metal one the device comes with and the $99 factory articulating mount. This mount is solid as a rock and height adjustable, one thing the factory mount is not. Highly recommended for Flex Maestro users.

Very sturdy stand, monitor can move from position even with the bottom of the stand to about 6" above the desk top. Stand is heavy and will not tip over. Easy to install to monitor.

Using this as a stand for a portable display. It is VERY difficult to move this into the right position due to how tight it is, and there is no way to loosen the joints at all to be able to make it easier. Other than not being able to position it easier, it does the job, I suppose.

Works really well - lots of adjustment points and holds its placement. We used on 22" monitors and have had no issues.

This is a great, heavy duty stand. We had an old monitor in a very tight spot, and it would not stay leaning at the proper angle for everyone to be able to see it comfortably. At first it seemed impossible to move, but once the monitor was attached, it moves much easier. The stand stays fully under and behind the monitor so quite compact, not taking up excess space we do not have. Will be buying another one soon for my other monitor set up.

Solide et pratique, utilisé pour un écran pc tactile au pied mal conçu. Avec ce support, le problème est réglé.

this unit is exceptionally solid. with a 15 inch touch screen it does not bend or give (the cheep monitor on it will but not badly so) For my touch screen the Vesa screws where a little to long so you may find it handy to have some screw washers around when you attach the two products. If anything the product could use some kind of cable clamp at its base. You may want to check the touch screen you might purchase to work with this as for mine only two Vesa Screw inserts where available and you probably want at least 4. Regardless, quite pleased with the product

Works, for a bit. then will start drifting downwards and to the side while you try to work. becomes unusable after a couple months of actual use.