FROZN A410 ARGB White - 6" Height White Air CPU Cooler with ARGB Lighting, 4×Ф6mm Heatpipes, 120x120x25mm FDB Fan, TDP 220W, Intel LGA1700/1851/1200/115X; AMD AM4/AM5 (152mm in Height)

Was a little confused after installing it, as I seemed to be getting the same temps on my i7-4790 as I did with my stock Intel Delta cooler. But, I soon realized it was using the same fan curve my motherboard had dialed in for it. After going into ASUS AI 3 software and running the automated fan tuning, then adjusting my fan curve to 10% at 35°C, 50% at 48°C, and 100% at 68°C my temps are several degrees lower across the board and much more stable. Mind you, I have a very old custom Apevia X-Sniper G case which only allows for 3 120mm case fans. One bottom front intake, one side intake affixed to the acrylic side panel, and one rear exhaust. With only 2 of those useable with the cooler installed due to it's height. Which I think adds to the quality of this cooler. I had to remove my side intake fan due to the cooler's size interfering with it, and tape off the inlet holes to ensure proper airflow and avoid negative pressure. I chose this cooler because it is just a bit shorter than the SE-224-XT, which has very good reviews, to ensure it would fit my case. So it's a great option for those with a minimum clearance of 255mm. Oh! Another important aspect is that I bought an additional matching ID-COOLING AF-125-K fan to utilize a push-pull config on this cooler also. The fan included doesn't have a PWM daisy chain connector, but the AF-125-K does so you can hook them together and they become controllable as a pair via 4-pin motherboard fan connector. Though, according to testing with other coolers, push-pull vs pull config only affects temps by 1-3°C in most cases. I also have 5.25" and 3.5" drive bays fixed to my case which sit flush and directly above my front 120mm intake fan. So my case is a bit crowded and has much less capability for airflow than modern cases. Packaging is very nice inside and out. Manual contents are decent. I easily figured out how to assemble and install it. Though there was an LGA 115X descriptor missing on the first page, it is mentioned elsewhere in the guide. Fan is superb quality, but missing a daisy chain connector. Includes 4 fan mounting brackets to utilize a push-pull config with an additional fan later, and should be compatible with any 120mm fan of typical thickness. My mounting brackets had some paint chipped off of them leaving a rough surface, but not worried about that. The 4 copper heatpipes are sandwiched between what I assume is brushed aluminum. A flat surface and mirror finish. One thing that did catch my eye is that there are a few very small gaps on the edges between the copper and aluminum on the bottom, which tends to catch q-tip fuzz while going to clean it, or could trap residual thermal paste after applying it. But, as far as I know and can tell this doesn't affect the temperature threshold. Though it is a bit concerning that old paste could get dried up and trapped in there. All in all, for the overall quality, aesthetic appeal of the design, ease of installation, and thermal results, I am very happy with this purchase. Where I was close to overheating or receiving temps around 75°C while gaming with a stock Intel Delta cooler, now my temps stay mostly under 70°C even while playing GTAV or RDR2. GTAV saw the largest thermal drop - where it was reaching 80°C it now stays under 65°C even while zooming around in a vehicle. I would highly recommend this cooler for quite possibly the cheapest way to get temps under control via air cooling. Not to mention how versatile it is between multiple generations of AMD and Intel sockets. And with it being just a bit shorter than most standing air coolers, it's sure to fit in almost any ATX/mATX case - even if you're like me and still rocking a case from the mid-2000s.

I waited on getting an air cooler for a long time due to a few things: Ram clearance, height clearance, aesthetics, and price. My PC is custom-built by another company, with the parts handpicked by me. While I picked my parts based on friends' recommendations and a general gist of what I personally needed, after three years, I went into looking for an air cooler for easier maintenance and long-term reliability. I have a mid-case tower, and my RAM sticks are way too high for the big chonky air coolers on the market, and I wasn't going to spend more money just to get better clearance of 32 GB of RAM. That would be a total waste, and after some research, I stumbled upon this brand. I was replacing a 120mm AIO (which I know is essentially pointless unless you lack space or airflow), so finding this air cooler that not only is perfect for my RAM clearance, but also meets my height clearance too. I'm thankful this air cooler doesn't have those annoying nubs at the top, because I don't think I would've met my height clearance otherwise. The design is super slick too, which makes my PC build look real nice, so that's a bonus. I'm using this to cool an AMD Ryzen™ 7 5700G, which is a low TDP CPU of 65W, so the cooler will do its job well. The cooler and fans are well made, and installation was a breeze. The fans runs my PC cool with little to low noise if you adjust the fan curve. It depends on the time of year and where you live, but since I live in a cooler area, my idle temperature sits nicely at 30C and during some gaming sessions with Chrome and Discord in the background, between 47-55C. However, I do have other fans installed for more optimized airflow, so other people’s results will vary. The price is just right, and certainly beats similar air coolers that go over $100 for the same performance. I highly recommend this air cooler if you're looking for RAM clearance, decent CPU cooling, height clearance for mid-sized towers, and a slick design to boot.

Im really satisfied with the performance of this cooler, its size is perfect which gave me room for the ram. The mounting was really easy with the instructions and the quality felt really good, there was a couple of really small scratches on the fins but they were barely notable. The performance is pretty good, it’s able to keep the i5 12400f at a cool 60-65 degrees under 100% usage at 70% fan speed. The noise is pretty minimal but at high usage it’s a lot more noticeable but not enough to distract you or make you concerned. Overall would recommend for people who want a cheap but well built cup cooler.

i bought this cooler to cool a ryzen 7 7700x it works fine for gaming but i did have to set a temp limit for 85c in the bios it does thermal throttle a little but i have not seen a loss in gaming performance its very easy to install it is a little loud when gaming and it fits inside my o11 dynamic it comes about a half a mm from touching the glass and looks good in my case.

building a complete computer system

Beautiful, strict, not bright, not so cheap but ok Almost enough with R5 7600X, I undelvolted my cpu from 1.450V to 1.250V(3 clicks) and locked to 5300mhz and it has 60-76°C in games (depends of game, ~~70°C in Squad) and 90°C at the hardest cpu stresstest(10 mins) If you want lower temps - buy the same but with 6 bronze tubes

マザーボードにAM5用の土台を装着後、CPUファン本体をネジ2本締めて固定で取付完了です。 手順はシンプルなのですが、最後のネジ２本がなかなかのクセモノでした。 位置が合わず、たった2か所のネジ締めに20分ほど苦戦して取り付けたという感じです。 努力で何とかなる範囲ですが、そこだけ少し残念でした。 静穏、冷却性能には満足しています。 ちなみに付属のグリスは３回分くらいあります。

Mounting was easy, seems to be a great cooler for a good price and looks nice. Using the thermal paste supplied, this cooler kept an i5 12600k below 70c running cinebench whilst being very quiet. It will work well for any use

Für den Preis und Optik Super