Peachtree Woodworking Supply Pro Grind Sharpening System for 6 Inch Grinders to Sharpen Lathe Turning Tools, Chisels, Skews, Bowl Spindle Gouges •Includes Setup Blocks and Quad Jig for 6 inch Grinders

I read all the reviews. I like to start with the 1-star reviews and work my way up. I don't know if the manufacturer addressed all of the issues, but I didn't experience any of them. The material used is even heavier than I had hoped. The cams and arms slide smoothly and lock without issue. I really like all of the different setup jigs. They are made of plastic but they are heavy duty and I see no reason why they won't last a lifetime. They aren't used under pressure or with a spinning wheel. I can't see a reason why plastic isn't a great choice for these jigs. The brass tightening wheel is secure to the steel screw. I tried very hard (with only my hands) to break the two apart and could not. I'm very mechanically inclined and I found everything very easy to understand and install. Everything was packaged with professional care. Not a single scratch on any piece. The finish on the parts seems very durable. A few of the welds (for example on small nuts that allow for the thumb locks) seem a bit small. But there are four on each nut and they are all solid. They don't have to take a lot of pressure so I believe they will be more than ample. (I'm just one of those guys that thinks more weld is better than less. However on these smaller nuts, more weld would probably cause way more issues and like I said, I don't thing it is necessary.) I would not hesitate to recommend this product to anyone. I did see that some people ordered 8" when they really needed 6" grinder versions. But the manufacturer is very clear in their description and on the box which one you are ordering. May 22 Update - I've been using the jig for a couple of months now and I really like it. I get perfect grinds on my lathe chisels every time. Since my angles are always the same, sharpening takes very little time and removes very little metal. I sharpen before each project and run a project every-other-day. Very nice product!

I purchased this to sharpen my wood lathe tools. I am a retired machinist so I am very familiar with what it takes to fabricate things. The entire unit is extremely well constructed, and the workmanship was way above average especially for custom made items these days. It was packaged perfectly, even though it was not in an exterior box it arrived in perfect condition. There is quite a bit of assembly required, and it does require measuring and drilling holes to mount the components, but I am sure that anyone who is going to purchase such an item will have no problems at all. The feature that sold me on this unit versus others on the market was the fact that this can be set up to sharpen any of the tools that I have, gouges, skew, scraper, parting tool, etc. There is no additional components needed to sharpen any of these, and additionally my wood chisels as well. If I had to find any sort of feature that could use improvement it would be the angles that the Pro Grind is set up to achieve. The documentation does not specify the angle, just a type of tool. I would like to see something for example "set to position #1 for 55 degrees, Position #2 for 40 degrees" etc. This way I could grind the tool to what I chose. Other than that, I can not find fault with anything in this system. I mounted mine on a 14"x18"x3/4" piece of plywood, and had to attach a smaller piece of plywood for the grinder to sit on to raise it to the proper height. The base is large enough for me to drill holes to store the various setup gages and places for the various fixture pieces, as well as a small dish of water in case I need to do some aggressive grinding and need to keep the tool cool. All in all, I am very pleased with this addition to my shop equipment. Based on other systems I looked at, the Pro Grind is not only very cost effective, but will sharpen a wider variety of tools. Recommend highly.

Update: I've figured out how to reduce the slop in the bases and that has helped. Unfortunately I've noticed that the large depth gauges attached to the end of the v-arm are interfering with getting a proper grind on my bowl gouge wings. I finally took a hack saw and cut the guides off. I ground down the edges on the v-arm smooth and it works much better. I took a file to the two depth gauge pieces that I removed and screwed them down to the plywood base. I’ve also found the the platform that I had issues with does work very well with rolled edge skews. I think that if I soften the bottom edges of my scrapers the platform will work with those as well. Adding a star on to my review. It does work but there are a few problems that are holding the review to 3 stars. When you pull the handle to lock the v-arm into the base the v-arm moves. It moves enough to change the angle of the grind but since the amount it moves is inconsistent you have to move it, lock the handle, see where it moved, unlock the handle and repeat until you get the angle just right. It takes a few times each time you need move the arm. The other issue that I have is the grinding platform. It’s aluminum and one corner was bent and scratched when it arrived. I was able to make it flat again but it’s not super pretty. It should be a steel platform since you’re running hardened steel tools over it. All that aside I can get a consistent grind on my tools with a little extra work to set the arm. Once the v-arm is in place you can touch up your gouges quickly enough that you won’t hesitate to go to the grinder while turning. The multi grind jig is easy to use and it works. The magnetic micro bevel block works well and provides 4 different bevel positions. The multi angle quad gauge works fine but I worry about the plastic’s longevity. Only time will tell if the plastic holds up.

This is a great sharpening system. I have used it to reset the edges on my turning tools and now get consistent grinds each time. It also takes me seconds to touch up the edge of my current tool so I find I sharpen more frequently because of how easy and fast it is to do, which of course gives me a very clean cut and better performance. I used the low speed, Bucktools 8 inch grinder, though I had to raise it an inch off the bench to accommodate the sharpening system.

Delivery was prompt,well packaged with very clear setup instructions. I watched the U tube instructional prior to starting the assembly. It went very well until I went to insert the long chisel slide arm,it kept binding halfway in. After a bit of frustration I realized the slide tube had a distortion of about 60 thousands in the center. I sent an email to the vendor and got an immediate response. I provided my order number and address and recieved a response within hours that a replacement was on the way. WOW, that's great customer service!! Once I got around that little problem,the system works great. My chisels all look much better then they have in a long while!

Wish I had used this system years ago! It allows me to sharpen my lathe tools consistently and in a much shorter time than it used to. Really really good!

I am writing a review because the first two reviews of this product seems unfair to me. One review complains of a slow delivery time. Mine was delivered to the UK as fast as I could expect and I could track it throughout. I had an issue with one component and I contacted Peachtree who sent a replacement, which was also sent quickly. The other review complains of frustration setting it up. It isn't possible to give exact instructions due to differences in grinder sizes. fitting the arms under the wheels does require adjusting the height as the grinder stand will vary. I would guess that this system will work better with an 8 inch grinder because the wheel may be further away from the motor body. This is most obvious when grinding an Ellsworth type profile on the motor side of a gouge. A smaller head on the jig, like Ellsworths own jig design avoids this problem. However the difference between 6 and 8 is just the plastic setting pieces, the rest is the same. The larger the wheel the flatter the bevel and it seems to me this matters most with a skew bevel. The adjustable platform has been very helpful with speedy scraper sharpening. This pro-grind jig system is sturdy and well made, sharpens many different types of woodturning tools and doesn't deserve low star reviews. It isn't the perfect solution, but I am rating it for what it is at the price I purchased it.

Excelente cálidad de los materiales. Facial de poner. Fácil de usar. Excede las espectativas. Deja las herramientas con el ángulo adecuado. Viene con guía de ayuda.

Good product