VEVOR Dirt Bike Lift Stand, Motorcycle Jack Lift Stand 440 lbs Capacity and Hydraulic Lift Operation, Adjustable Height Hoist Table, for Dirt Pit Bike Repair, Maintenance, Dirt Bike Accessories

Works well on dr350 and lowers slowly

Works really well love the adjust-ability saves lifting an MX bike on it. Only thing better would be if it had an indent so it naturally sat in Qtr positions then the lock feature would be easier and more use.

This works well but can be a touch unstable with our light trial bike. After a bit of practice it’s fine and does the job, happy with purchase

Well made

Easy to use stand that's good value for money

stand looked ok but the quality was lower and the stand flexed alot, it really needs to bit a bit stronger to hold full sized dirt bikes, would be fine for kids bikes

The base could have done with being wider but it works ok. Ensure you use the safety lock

I've just received this and put it together. I got this for my new Voge 300 rally it holds the bike ok the only problem is when you put your foot on the lifting part and lift the bike up and then put the safety clip on to stop the lift from dropping you then take the clip of to drop the stand it does not go down I'm have to use my hand on the handle to pull it up to lower the bike and is hard work I'm not happy about this not sure if any one else has had this problem or less it's because it's new if it does not sort its self out ill be sending it back

Buena calidad en todos sus materiales, excelente funcionalidad, lo recomiendo!

Perfecto para motos lijeras, puede levantar una crf 300l como si nada, le tuve que poner grasa porque rozava bastante e iba duro al principio, pero por el precio un 9/10.

Update 5-21-24: I bought a second dirt bike (2023 Husqvarna FC250). A full motocross bike. The stand also works great with that. I just set the platform higher so it will just get both wheels off the ground. And then set the locking nut underneath it snugly. Works great for this bike too, so I bought a second one. And here is a tip for people: Rather than banging on the arm on the locking nut with a hammer or mallet and risk breaking off the arm.. (You want this positioned snug against the base of where the spindle comes out- to provide more stability). Instead position it so it is snug, and then rotate the platform to get it tight. I have a 21 Honda CRF250F and this stand is perfect for what I need, and at a good price. I also have a regular stand that is 17" high, and trust me, its not that fun flipping a 265 pound bike up on a 17" stand. I can usually do it, but sometime I have to do it a couple times, and then reposition it a bit after. With this stand, I can just position it under my bike and push down on the lever. So much easier! A couple tips for people: Keep the height as low as it can go and still get the bike as high as you need. For my bike, I can leave it on the lowest setting and it can still get the bike high enough for me. If I want the back wheel off the ground (to say lube the chain), I position it more towards the rear, and let the front wheel rest on the ground. No need for me to get both wheels completely off the ground at the same time. That way it stays very stable. I also raised the platform until it just barely fit under my bike, and then it raises both tires a couple inches off the ground. It will sway a little like this if you push on the bike, but it still feels fine to me. If you have a full MX bike with more ground clearance and suspension travel, you will probably need to raise the platform a few inches.. I expect it might feel a little less stable. So I would set the platform only as high as you need it to be to get the job done. Also there is a locking nut on it, so I rotated that in place and then rotated the platform until it was snug. Works for me. I also like the hydraulic thing on it, to make it drop slowly rather than just plopping the bike straight to the ground when you release it... And I don't know if this is how they all ship, but mine had an extra corner pad (for the "feet") and an extra c clip for the pins. I really like the convenience of this stand! Hope this helps someone.

Super

Super Artikel TOP Motorradheber. Gute Verarbeitung, gute Funktion, sehr stabiler Motorradheber / Hebebühne. Wir verwenden diesen für eine Motocross und dazu ist der Heber sehr perfekt. Dank des Zylinders, lässt sich das Motorrad sehr einfach nach oben heben und beim herunterlassen, fährt das Motorrad wieder auch gedämpft nach unten. Absolut zu empfehlen.