DTF Transfer Film Roll 13"x328FT,Double-Sided Matte Pretreat Film

The product will most likely produce the best quality with a DTF printer, but they are extremely expensive for the amount of fabric printing I do. I tested using an Epson Sublimation printer and after perfecting the temperature and pressing time, I was super happy with the results. So, contrary to manufacture's statement, which reads, "Must use with DTF ink. Regular ink, sublimation ink can not be used, with the same brand DTF transfer film, DTF ink and hot melt powder, the transfer effect is more perfect." While that may be true, for a more "perfect" transfer, I disagree entirely that "sublimation ink can not be used". YES! Sublimation ink can be used. :-) What did I use: Epson SureColor F170 sublimation printer with genuine Epson Sublimation inks WELACER DTF Transfer Film Sheets Godora Transfer Powder (DTF White Powder Hot Melt Adhesive) - You can not skip this step! VEVOR Heat Press (12" x15") Tips: PRINTING ON THE TRANSFER SHEETS: This slowed down the process but made it fool-proof 100% of the time. These sheets are very thin. Putting a single (or multiple sheets) in the printer tray caused a misfeed, and printing started midway down the sheet which ruined that sheet. When that happened, I didn't want to ruin any more sheets, so I taped the top of the sheet to copier paper (glossy side of transfer sheet against the paper so it prints on the dull side of the sheet). I used only a sliver of tape (about 3/8" in length) on the top left and top right. I place only one set of taped sheets at a time in the tray. It fed perfectly each time. I prepared all sheets with the copy paper so it was ready to use when I needed it) APPLYING THE HOT MELT POWDER: Immediately after printing, carefully and quickly remove the copy paper, lay the transfer sheet on a flat surface (I use a 3" deep 11 x 14" bin), shake the transfer powder over the entire printed area, fully covering it. Let it rest on top for a few seconds; at least 15. Grab the sides of the sheet firmly, lift the sheet and curl the sheet, allowing the powder to roll from side to side, top to bottom over the printed image; don't agitate, you might smear the printed image. Slide all excess powder off the sheet and into the bin. Holding the sheet firmly along the edges, Gently tap the edge of the sheet inside the bin to release remaining excess powder. Visually examine the sheet. If you see excess powder on the non printed areas, gently tap again. CURING THE POWDER before the transfer: The powder needs to "set". There are special ovens for this, but you don't need the additional expense. I use the heat press, about an inch away from the platen, and place the transfer sheet (of course, powder side up) and leave it under there (380 degress) for 3 minutes. PLEASE TEST YOUR OWN SETTINGS! During these 3 minutes, I empty the bin of the powder, into a small plastic container so I can re-use it. I see people (on DIY videos), emptying it back into the original container. Why? You might end up mixing unwanted particles with the unused powder. In a small container you can see and remove any unwanted particles. But, that's just me. TRANSFER IMAGE ONTO SUBSTRATE: I highly recommend you "sacrifice" an actual garment that you plan to transfer onto, and test small areas at a time, multiple times on the test garment until you find the best temperature and timing. For my equipment, 380 degrees, at slightly more than medium pressure for 40 seconds yielded the very best results. Always press the garment first for about 6 seconds to remove wrinkles and moisture. Even though the powder has been baked, it can still be damaged if touched. So, eyeball the placement carefully before placing the transfer sheet onto the garment. It can be very slightly nudged if you need to reposition it, but I would not recommend it. REMOVING THE TRANSFER SHEET. Welacer states that the transfer can be removed while it is still hot (or cold). This may be true for DTF inks, but I found that for sublimation inks, WAIT until it is fully cooled off. Removing warm tugs at the fabric and takes a bit of effort to remove. It generally doesn't damage the image, but it will pull on the fabric and can nick off part of the image. When fully cool, it lifts off effortlessly, and no tugging at the garment. Important to note about this Seller: This is my second order of this product. I needed more sheets to finish a job and was thrilled that they were offering a nice discount this time around. Unfortunately, the discount was most likely offered because ALL OF SHEETS had fingerprint marks along two of the edges. Luckily, it did not interfere with print area, but, I am extremely disappointed. I would rather have paid full price if I thought the discounted product would be defective. The worst part: They inserted the sheets INCORRECTLY into the cellophane wrapper. There's a sticker on the wrapper that states "Print Side". The print side is dull and the non-print side is shinny. However, the difference between the 2 is very slight, so you have to view it at an angle to make sure. Well, these were inserted wrong. Had I NOT already worked with my first order (which was packaged correctly) I would have ruined a sheet or two. This would have been disastrous for a first-time user. There are other DTF Transfer sheets out there... I will try others before I trust this vendor again.

Very good film and very good price

🗣️ STAR UPDATE 🫶🏽 This was my second purchase & it’s ruined. The first roll was perfect & I loved the quality of my DTF prints. Opened the second box and the entire roll is defected. I figured it would be the first few inches of film damaged but after feeding it through my printer, the defects were nonstop. After reaching out to the company, they worked very quickly replacing the product. I actually received the replacement before the tracking number was issued. That’s what you call A1 customer service!!! I will definitely be purchasing again & again & again.

love it

Received a defective roll, was contacted by email that they are going to send a replacement. Hopefully the replacement is better and not like this roll I really love their ink and powder, so I’m hoping this was just a bad batch . Waisted a lot of ink and time! The entire roll has white globs on it that affect the print, if you scratch of the globs it removes the film coating so completely unusable.

Uhm! My new favorite dtf film! Seriously. It peels like butter straight off the hot press. The old film I was using was destroying my shirts. Not this one. I’m seriously amazed at how well it is!

Unfortunately, I had a disappointing experience with this DTF transfer film. The film appeared to flake and shed onto the paper, which caused problems during printing and ultimately ruined my job. I purchased it as a backup and didn’t need to use it right away, so the issue wasn’t discovered until later. This may have been an isolated or bad batch, but it was my first time using this brand. I’d be open to trying a replacement or different batch if offered. By the time I encountered the issue, it was outside the 30-day return window. Based on this experience, I would be cautious about relying on this product for professional work.

El producto llego en perfecto estado, y es igual a como lo describe el vendedor. Excelente producto. Totalmente recomendado.

Good

I received this product and at first it was not what I expected. The product itself works fine but it was matte and the ad said clear. I contacted the seller and they communicated right away and offered a very fair resolution. I am very satisfied and very happy with this outcome.

works great. very nice quality. and color for hack comes out great

Absolutely love the product. Went to order again and noticed the price hike 😭 won’t be ordering again till the price drops.

Works as intended. I would recommend