Fuji Spray 2203G Semi-PRO 2 - Gravity HVLP Spray System

I had no prior experience with HVLP spraying. There’s quite a bit of a learning curve with regards to handling, general technique and such, but as for the product itself it was very straightforward to use and gave me no issues. The provided documentation and charts on which tips to use for which application were helpful. Very simple but quality rugged setup. Once I had a process figured out, clean up was VERY easy. I went with HVLP in part because I did not want to deal with flushing out hoses, and that aspect worked out great. I was able to switch between different materials with no problems. I used it for both painting and applying a polyurethane finish. Paint was an oil-based primer and water-based urethane enamel. I thinned in both cases and used a 1.8 tip (which you need to buy separately) and it applied the paint very well despite concerns of it only being a dual stage turbine. My only criticism, if you want to call it that, is this doesn’t do everything. I have plans to paint interior and exterior walls and that kind of job, while technically possible, would be a bit overkill for this unit due to how much paint it can hold. This product seems like a decent value for the hobbyist (or “semi pro” ;) who wants to achieve great results with no fuss. A bit pricey, but the quality is high, and the results good.

Over the last two years, I wrote something of a book below, so I'll summarize up top. For spraying latex, this setup requires considerable thinning. You can get very nice results and I don't really mind the thinning, but spraying thin paint is pretty miserable, particularly on any vertical surface. For spraying lots of latex, I'd upgrade to the Mini-Mite 3 or 4 to spray with less thinning. For spraying clear finishes, particularly those designed to be sprayed (I've used a couple of products by Target Coatings), this little machine is spectacular and wholeheartedly recommended. Original Review: I am a weekend woodworker with lots of projects that involve painting (mostly with latex) and applying various clear finishes. I've been casually eyeing assorted HVLP systems for several years now and seriously considering for a few months. Because I wanted to be able to spray latex, it seemed like the Mini-Mite 4 was the right choice, but I just couldn't justify the $800 price for the amount of spraying I plan to do. The semi-pro 2 was at about the price I was willing to pay, but I was concerned that the two-stage turbine would be insufficient and that there were no reviews (hence this review). The prospect of rolling/brushing a big painting project finally forced the issue and I crossed my fingers and ordered the semi-pro 2 with the gravity cup. I now have a couple of hours of spraying under my belt (that's a lifetime total, it's worth noting that I'm new at this) and I couldn't be happier with my decision. In the last few days, I sprayed a couple of big bookshelves with latex primer and paint (Sherman Williams multi purpose latex primer and All-Surface Latex Enamel) and the whole system works better than I dared to hope. I was a little worried the "M" gun would be somehow low-end or lack features, but it's really, really nice. Again, I'm new at this and have little to compare to, but I'm not sure what else I could ask it to do. The spray pattern is adjustable from a wide fan to a tiny spot and you can rotate the pattern anywhere you like. Since I was spraying between shelves, I had the gun tipped over pretty far and it never hiccuped. The gravity cup holds 400 cc's, which isn't a whole lot. So far, that's been about one coat on a bookshelf. If you plan to paint big stuff, the 1 qt cup is probably better. As for the turbine, it's a little blue box. A noisy little blue box, but most of my tools are noisy, so I wear hearing protection and it's just fine. A quick update, I measure 92 db a few feet away, which is really very loud indeed. I measured a small, noisy shop vac at about the same distance and got 86 db, which is roughly 4X quieter. Still not a problem for me, but perhaps worth noting. I regularly use this in my basement with a baby sleeping on the second floor and she doesn't seem to mind. My concerns regarding the two-stage-ness of the turbine seem to be unfounded so far. Fuji includes and excellent instruction manual (also available in PDF in the FAQ section of their website) that recommends thinning paint and checking with the included viscosity cup. The manual also recommends a #4 (1.5 mm) tip for latex. I sprayed primer with the included 1.3 mm and paint with the 1.5 mm tip and while the 1.5 mm tip definitely sprayed faster, I think I could have managed with the 1.3 mm tip. I followed the thinning instructions with both the primer and the paint, thinned with roughly 20% to 25% water, added some Floetrol, and sprayed a nearly perfect painted finish. I would recommend practicing a fair amount on scrap wood, cardboard boxes, etc. Cleaning up after spraying is very easy and takes me maybe 10 minutes. One thing I'm confused about is how a four-stage turbine could possibly be better. Maybe you could spray faster or not thin, but this really isn't all that taxing for the way I plan to spray. I'm really looking forward to spraying some clear finishes next. Update: 11/17/2013 I've now been spraying latex for a couple of weeks and I have produced results ranging from truly disastrous to nearly perfect and pretty much everything in between. For my best results so far, I spray a relatively thick, heavy coat of primer (I've tried up to about 50 seconds in the viscosity cup with great results) with the 1.5 mm tip. This does produce some texture, but I end up sanding the first coat of primer anyway. I found that thin coats of watery primer never actually cover spots, fill grain, block tannins, etc. I generally follow with a second relatively thick coat of primer. Then, I switch to the 1.3 mm tip, thin my paint to about 25 seconds in the viscosity cup, and spray very light coats of paint. Much of what I read suggests that the thinner your paint is the better it works, but I found that if the paint is too thin, it's almost impossible to get any coverage and not get runs (the source of my most disastrous results). I experimented with heavier coats of paint and got a bumpy surface (not as bad as runs, but pretty ugly). Two or three thin coats seem to give good results for me so far. The resulting surface isn't glassy smooth, but is very lightly textured. Far better than I've ever done with a brush or roller and good enough for me. Still looking forward to trying clear finishes when this project is over. This is still clearly a 5 star purchase for me. So far, the included 1.3 mm tip would have been fine for latex. I now think I see the benefit of the more powerful turbines if they allow you to spray less-thinned paint. Thinning isn't really a hassle, but spraying watery paint kind of is. Still, for half the price, I'm happy to thin some paint. Update 2/21/2015 I finally got around to spraying some clear finishes. This summer, I sprayed some Zar Ultra Max waterborne oil-modified poly, which worked reasonably well. I sprayed a picture frame, I think, and it came out looking nice, but with a few small, pimple-like dots. I was able to sand these out, spray again lightly, and get a passable finish. The pimples may have been dust or dirt, as I was spraying outside. Zar doesn't appear to really market Ultra Max for HVLP spraying, so I recently ordered Target Coating's EM8000cv pre-catalyzed waterborne conversion varnish (targetcoatings.com), which is actually intended to be sprayed and includes specific instructions for HVLP (1.3mm to 1.5mm needle). I just sprayed a small cherry shelf with this stuff and my 1.3mm needle and it seems wonderful. I sprayed the first coat on a little thick by accident, sanded it lightly, and just applied a very thin second coat and the finish is absolutely flawless. It also dries to the touch in minutes, which should minimize dust and dirt. If your plan is to spray clear finishes, I can't imagine why you would look for any sprayer fancier than this one. Clear finishes are nice and thin and spray easily and beautifully. I also wholeheartedly recommend ordering some finish that's meant to be sprayed, since things get really easy (no thinning, etc). Finally, google conversion varnishes. Apparently, they dry too fast to be brushed, which is why home stores don't stock them, but they're tougher than polyurethanes and easy to spray. Newer waterborne conversion varnishes are (allegedly) just as tough and have startlingly little odor. Look at both Target Coatings and General Finishes. They both offer bewildering assortments of water based lacquers, waterborne oil-modified polyurethanes, waterborne conversion varnishes, etc, all specifically intended for spraying. If Amazon would give me six stars, that's how many I would give this sprayer. I'm amazed in retrospect that this sprayer is as inexpensive as it is. Update 12/20/2015 I recently sprayed a large bookshelf project with the Target EM8000cv pre-catalyzed waterborne conversion varnish and I am really, really happy, both with the Fuji and the Target varnish. For about the first time, when I look at the finish I can't really find anything to complain about.

I bought this unit to use on a fabric covered aircraft restoration using the Poly-Fiber system. It worked flawlessly spraying both Poly-Spray and Poly-Tone. I bought the gravity feed but you might consider the suction feed for painting under the belly as it is more difficult with the gravity feed. One operator error that I continued to make repeatedly is something that you will do also if you are only used to compressor spraying. It is opening the valve on the gun feed end of the supply hose before spraying. The spray gun goes on with a quick connect just like a compressor hose. However, you then need to remember to open the valve to feed air. If you don't, the gun has just enough pressure to spray a small stream of product over what you are working on. I now remind myself but counting the two steps every time I connect 1) Connect gun, 2) Open air valve. It sounds simple but it got me more times than I care to admit. The quality of the gun is excellent. The hose seems like a quality one that should last for a long time. The turbine itself is loud but I guess there is not much they can do about that. The spray gun holder that you mount on the unit I found very useful and convenient. My dad liked it enough that he bought one as well. Cleaning the gun is very easy and I only had one clog that i was able to spray out. Controls of the spray gun are very simple and intuitive. I highly recommend!

Purchased this product for a combination of projects including latex paint for cabinets, wood finishes including lacquer and shellac, and automotive finishes. So far we've completed the cabinet project and are very satisfied with the product. We purchased the #4 tip (1.8mm) and also utilized the 3M PPS 2.0 system to prime and paint roughly 30 cabinet doors. Technically this is probably exceeding the limitations of the product, but with careful setup and consistent thinning, we were able to lay down a professional quality job on our cabinet doors. Fit and finish of all components is top notch. Gun disassembly is easy and intuitive. Thorough cleaning does require a more well equipped cleaning kit than is furnished with the turbine. The turbine is surprisingly loud, comparable to a large shop vacuum. This is not a problem, just an observation. The large supply hose is nearly unmanageable. Fuji makes a 6' whip hose that I find to be 100% necessary, which is not included with the turbine kit. I imagine spraying with the thick rubber supply hose would be nearly impossible to work with. Overall the product is very high quality, well put together, and functioned exactly as expected. This is my first experience with HVLP, and the results were definitely professional quality after getting everything dialed in. Can't wait to spray some woodworking projects.

I bought the Semi-Pro2 with the M series gravity cup. I added the whip hose and the .08 and 2.0 tips for the different finishes I routinely use. I have used the system almost daily for two weeks. Overall, I am very satisfied with the system, its easy set-up, standard cleaning (spray guns are never quick to clean, and I am meticulous with my tools), consistently getting high quality results. I have used HVLP sprayers with air compressors for many years and wanted to try the turbine systems. After reading dozens of reviews, I chose the Fuji system for several key reasons, including reviewers' opinions about the quality of the turbine, versatility, interchangeable components, accessory options, all at a more-than-competitive price. I bought the Semi-Pro2 because I did not want to get the top line Q-series without ever having used a turbine system. Depending on longevity of this system, I may upgrade to the Q-series in the future. As with any HVLP sprayer, there is a significant learning curve requiring practice and developing technique. If you get lap lines, drips, orange peel, more paint on your walls than your project, etc., go online, watch instructional videos, read articles, practice with different finishes - all these problems can be addressed with settings (assuming your equipment is sufficient for the job). Semi-Pro2 Gravity Feed Likes and Dislikes: The finished projects have been excellent. The spray nozzles are obviously well manufactured because the finish is flawless. I noticed a few very minor things that made the difference between a 4- and 5-star rating: - The gravity feed cup is small. My compressor HVLP system has a larger cup which means I do not stop to refill as often. Fuji offers the larger bottom feed cup which would resolve that issue. I have never used a bottom feed cup, and I like the idea of gravity feeding the gun instead of a diaphragm component, so I chose that option. Obviously the larger bottom feed cup would address this point, but a larger gravity feed cup would be my first choice. - The screw-on cap for the gravity cup is not great. It does not seal properly even with a new gasket. It appears this could be resolved with a different (better) thread pattern for the "screw" which would tighten the seal more gradually and therefore efficiently. My old gravity cup does not leak at the cap, so Fuji could do the same. (Very small leaks, but leaks.) - Fuji recommends not taking apart the feed line from the cup and gun, because it is factory sealed. I prefer to remove the line so I can be sure it is fully cleaned without any residue which could be problematic on the next project. - The nozzle cap has worked perfectly and shows no signs of flaws. However, it appears as if it is a plastic cap coated with chrome skin. To date, it has been perfect, but it feels like it could break or crack easily if dropped. I know, don't drop it, but a heftier feel would give me more confidence is its longevity. - The air control valve is a 90 degree ball valve. Convenient and easy. I prefer my old HVLP air control valve which allows for a better fine tuning control. It is important to note that I purchased the system with the M-series gun which is a more basic model. Fuji's higher end systems (Q-series turbines) include the T-series guns, which may be a superior product to the one I have. If you are still reading this, you have too much time on your hands. However, I highly recommend the Fuji system, especially for a user who has never used a turbine system. I will end this by saying that I contacted Fuji before purchasing the Semi-Pro2 and they were very responsive to my questions, encouraging additional follow-up or technical assistance if needed (which to date I have not).

This system is top notch! Fuji Systems are very high quality and built very well. It cleans very easily, and is easy to setup, even for beginners. You can tell just by handling them they are quality components. I had one of these systems years ago and wanted to purchase a higher model, but this unit provides such great results I cannot imagine what the higher end models produce. I would not purchase any other brand of HVLP spray system other than Fuji, they are the best!!

Was I opened the packaging of the Fuji Semi-Pro2 spay gun and turbine, my first thought was how good it looks! As I pulled everything from the packaging I marveled at the quality, especially in light of the price I had paid…what an awesome value. The feeling, finish and workmanship are stunning. The high quality of materials of this kit are usually only found in much higher priced equipment! Then I plugged in the turbine and hooked up the 25’ hose (this is awesome plus…freedom of movement) and spray gun, just to make sure everything fit together and worked properly. Well it did fit and work perfectly. I pull the trigger on the spray gun and “played around” adjusting the settings, then my attention turned to the turbine. I was surprised at sound level…It wasn’t silent but it wasn’t annoying either…quiet enough that it wasn’t the first thing that drew my attention. Then I noticed the holder for the gun was missing on the turbine, so I immediately searched through all of the boxing and foam padding but did not find it. I located the customer service contact in the manual and sent a short email explaining my situation and included the Amazon order number as well as my physical address, along with a photo of the turbine without the holder. My hope was that Fuji just might send a gun holder to me without a bunch of back and forth emails. I also thought, this will quickly give me an indicator of the Fuji customer service quality! I received a typical confirmation reply that my email was received and I would be contacted by a service representative ASAP. To my surprise, in less than 24 hours, I received an email apologizing for the missing holder, indicating that one would be shipped to me immediately…no questions asked! Wow, didn’t expect their response to be that quick and that easy…that’s what I call customer service and support! I’m a woodworker and furniture refinisher, and this unit is a replacement for my old HVLP spray setup. I haven’t been able to actually finish anything just yet due to weather conditions where I live, but things are looking better in the near future, weather wise and I can’t wait to spay finish a couple pieces waiting in the wings…I will definitely be back here with an update and hopefully a video of this system in action. In the meantime, if you are a hobbyist or a pro on a budget, like me, looking for a great quality HVLP system at a very reasonable price…I’d say don’t hesitate to give the Fuji products a try. Hope this helps anyone on the fence make a decision to purchase this Fuji spay setup! I’m betting you won’t regret it. I’ll be back with more soon… Well I promised to get back with a follow-up review of this spray unit. I’ve attached a couple videos to help explain my review. First of all the missing gun holder was sent in a couple days after explaining to Fuji. I was blown away at the quality of the gun holder attachment. I was expecting a pice of pressed metal with a short metal rod welded to it…what I received was a very well finished cast aluminum holder! My first thought was, if they took this much time and quality material for a simple gun holder, imagine the quality of the inside of the turbine! Secondly, the turbine and gun combo worked flawlessly! I was able to spray un thinned latex without out clogging or splatter! I’m very happy with the results. My shutters look great! Check out my watched videos.

I'm using this HVLP system for spraying finish on guitars, so I have no experience as far as using it for thicker paints. With that said this is a very high quality HVLP spray system that atomizes and lays down a very nice coat of material. I was a bit hesitant at first due to the high price but when I saw them on sale for black Friday I had to give it a try. I was also leaning towards this brand from other wood workers recommendations (The Wood Whisperer). Likes: I like the fact that the Fuji systems are mostly made of metal's where other brands have a lot of plastic. This system also does not constantly bleed air as some others do so air is only coming out the gun when spraying. Cleaning is just as easy as with any high quality HVLP gravity gun, the stainless cup makes it easy to clean out and if you want to make it even easier you can purchase an adapter that will allow you to use the 3m PPS system. If you need to hold more material you can also purchase the Fuji bottom feed pot (the gravity feed cup holds less material). All the hose connections are secure and have quick release collars so I don't have to worry about the line blowing off and dust getting blown all over my project in the middle of a paint job. Dislikes: My biggest dislike is the type of hose, it is very big and bulky like an industrial water hose but there may be a reason they did this, It might give the air going to the gun more time to cool and less chance of moisture getting in the spray material. The only other dislike is the noise, this unit is very loud like an industrial vacuum cleaner but if you have used any other type of spray system like a separate air compressor and gun then it is no big deal as it is no louder then an air compressor kicking on. Overview: Even if I paid full price for the Fuji semi-pro 2 gravity feed I would still be happy with it. I am sure some of the cheaper units out there can give great results as well but I think the construction of the Fuji unit and some of the extra features and functions it has makes it worth the extra cost. As for Amazon, they are great, while I like to support my local business owners no one near me sold this brand and with the low price I couldn't resist. Also I originally purchased on open box unit that was supposed to be like new and was sold through Amazon but when I received it there was only the turbine unit, no hose or gun. One quick call to Amazon customer service and not only did they have a return label emailed to me but they also had a brand new unit sent out at no extra cost to me.

I've just done one project so far, an oak desk that I stripped down to bare wood. I wanted to use water based products only, which was also a tip offered by several reviewers, especially if you've a novice like me. The main reason I wanted to try a sprayer was doing the large flat top surface with a relatively fast drying product. You simply can't move fast enough sometimes to cover a lot of square feet with a brush or rag, and not end up with gooey overlaps or brush marks etc. Spraying takes that fear away, since its a very quick application. My project wasn't particularly easy, as I used a dark brown Minwax stain (applied manually since I wanted to rub it with a rag soon after applying) and then sprayed 3 coats clear top coat from General Finishes; it was not easy to see exactly what was going on due to the lack of contrast. I'm sure with practice I'll know how to arrange better lighting and whatnot. At times I was too trigger heavy on the desk legs and got runs, which I had to quickly rub off. The large horizontal surface was more forgiving and any heavy spots levelled off just fine. Clean-up was a breeze as many have mentioned. I expect I'll eventually get a short light 'whip' to make handling the gun easier. All in all, this appears to be a great product and having something made in Canada (my country) is welcome treat. Bob

Muy buena opción para no tener que usar un compresor. La turbina siempre está encendida lo que lo hace un poco ruidoso, pero no te afectan las variaciones normales de un compresor. La pistola tiene buena calidad, sólo le hace falta un soporte para la pistola, lo venden por separado.

Muy fácil de manejar y excelente calidad en los materiales, con resultados increíbles al momento de pintar

Update July 2023: I’m still so happy with this thing. I’ve used it easily 150 times to spray all kinds of stuff. Every time I use it I’m so impressed. Update Jan 2022: I've now had this about 3 months and have used it heavily, probably 50 times to spray various primers, latex paints and polyurethanes - all water based. I have to say it works beautifully. I am even more happy with it than when I first purchased it. I am getting a perfect finish every time. Why I didn't buy this sooner I don't know. My only complaint that has developed is the gravity cup prevents it from fitting in a gun holder or standing up. This makes it a pain to fill up. To solve that problem, I purchased the 3M PPS 2.0 system and added it to the gun. I think if I was to do it again, I would buy the bottom feed cup instead of the gravity cup, but now that I have the 3M system it's a moot point. Just keep in mind it requires 3 hands to fill the gravity cup. Fuji does have a little holder that screws to the turbine but that isn't practical at all as the turbine is far away and on the floor. If you buy this gun, I highly recommend adding the 3M PPS system. Original review: After spending the last few years brushing/rolling finishes and messing around with several of the cheap compressor driven HVLP guns and never getting a good finish, I finally bought one of these. I am somewhere between a DIY’er and a pro. Not new to this but I also don’t spray every day. I spent a ton of time researching and couldn’t decide between a turbine HVLP and the airless. I want to spray latex paint, polyurethane and lacquer and I came to the conclusion the HVLP was more versatile, especially after hearing about all the pump issues people seem to have with the airless units. Several websites mentioned that you needed a 4-5 stage turbine to spray latex and that perhaps this unit wasn’t the right one but I’ve now sprayed both latex (BM Aura) and polyurethane through it. I did have to buy the 1.8mm tip and thin the latex 10% (ish) but it sprayed perfectly. Fuji says 20-30% but I had no issues at 10%. I also can’t believe how nice the water based poly went on with the supplied 1.3mm tip. I am so impressed with this thing. I think the pressurized cup is a game changer for latex paint. It is pretty loud but is on par with a shop vacuum. Definitely not a deal breaker by any means. My only complaint is that the gun doesn’t fit in a traditional HVLP stand since it has the side cup. I hope Fuji comes out with a stand for the M series gravity gun. It would make filling a little easier. Overall I am very happy with my purchase. It sprays latex paint and polyurethane perfectly. The unit is clearly of high quality and I’m happy to deal with a Canadian company. I would highly recommend this unit.

After researching spray systems for many months (reading reviews, watching YouTube videos and such), I narrowed down my choices to the Earlex 5500 and the Fuji Semi-PRO 2. Both have excellent reviews, however the Fuji is more powerful, comes with a longer hose and just seemed like a better system -- although I based this on pictures and comments because I hadn't seen either in person. The Fuji also has a 47% higher price tag in Canada. After some back and forth I decided to go with the Fuji and am very happy with that decision. It's well built, easy to use for a newbie like me and from what I've read, has terrific customer support. I prefer to buy quality tools once rather than cheap stuff I'll have to replace later. I've found quality lasts a long time and the user experience is far superior than trying to save a few bucks with lesser offerings. I have never regretted purchasing Festool, Snap-on and Knipex despite the price premiums they command. The Semi-PRO 2 seems to be in this category based on my, admittedly, limited experience with sprayers. Keep in mind this is a 2 stage system, so it's the least capable in the Fuji lineup. However it completely meets my needs and I don't expect I'll need to upgrade. But if you think your requirements will change in the future, you might consider one of Fuji's 3 or 4 stage systems -- but be prepared for quite the jump in price. If you're new to spraying, here are some things you should do: 1) Buy the book/DVD combo called, "Spray Finishing Made Simple," by Jeff Jewitt. It covers everything a beginner needs to know and will save you lots of time and experimentation. 2) Get some paint strainer filters. I purchased the Ram-Pro 250 pack for $26.99 CDN. They seem to be good quality. 3) If you're spraying latex, get the larger 1.8 mm nozzle (Aircap #5 set). The Semi-PRO 2 comes with a 1.3 mm nozzle. All in all, I'm impressed with the system. Highly recommended.