FLASHFORGE ASA Filament 1.75mm, 3D Printer Filaments 1kg Spool-Dimensional Accuracy +/- 0.02mm, no Smoke and no Odor (Black, ASA)

This is FANTASTIC! I thought i had found the best filament ever when I bought Polycarbonate but this is even better! This is slightly stronger but slightly less impact resistant than ABS. Slightly weaker than Polycarbonate but Polycarbonate doesnt have much impact resistance if anything at all. I've printed various RC car parts with this and every single one has come out perfectly, its pretty much the God filament for me. Im yet to test the strength of a spur gear but I have printed 4 of them with this filament and the finish and strength are seriously impressive. As soon as I get paid I'm buying a few more rolls of this, from now on I'm printing EVERYTHING in Flashforge ASA!

Reasonable ASA filament. Prints come out great on generic setting of my Bambulab X1C

Really good filament, strong when printed, nice colour. Printed perfectly on my Bambu P1S with the "Generic ASA" preset. Fully recommend

This is the only ASA I've used, so I can't compare it to others. I bought it mainly because it was the cheapest available at the time from a brand id at least heard of. It prints great, really wasn't difficult at all to get good prints with; however, it DOES have an odour which is quite strong, mainly noticeable when I open the door to take out the finished print, it does smell during printing, however, nowhere near as strong. Prints are quality, super strong, and clean. Already bought again as I ran out and have more to print! Info - Bambu Labs P1S, Smooth plate 100 °C, 260 °C, dried for 12h @55c, why printing in 30 °C dry box, 20mm brim, max print speed 250, filament is calibrated for flow rate, flow dynamics, overhang angle and temps

This is by far the best ASA filament that I have used. The black is true black unlike some other brands that are a dark grey. I really am very impressed with this filament, it comes off the spool with ease, and the print quality is excellent. To get the best out of ASA I typically print at slightly higher temperatures than those that are recommended and use hardly any cooling. My printer is a Flashforge Adventurer 5M pro and is fully enclosed. For the money, this filament is excellent value and I will definitely be making this my preferred choice from now on.

This has become my go to filament for most things I print. Copes well with temperatures in car engine bays and not had any structural prints break apart from when I deliberately did so for testing. I do get a bit of warping off the bed when I print over 200x200 but I think that may be my fault for not having the chamber heater on. Overall, can't recommend this ASA enough.

This ASA proved difficult to print. Multiple parts could not be completed due to warping, which led to adhesion issues. I tested various bed temperatures and different build plates, but encountered the same outcome. It may be a settings issue; however, single-part prints were successful, whereas multiple parts (sequential printing) consistently failed.

I've been 3D printing for 6byears but never tried ASA as I didn't have an enclosed printer until recently. Someone I was doing some car parts for wanted ASA so thought I'd give it a go. This filament printed really well with the default printer setting for ASA. No warping or stringing and chamber temp was only around 30 degrees. Really impressed

Filamento ASA di alta qualità, perfetto per stampe resistenti agli agenti atmosferici e ai raggi UV. Ottima adesione tra i layer, finitura liscia e professionale. Ideale per componenti da esterno e parti funzionali. Un'alternativa eccellente all'ABS, con meno deformazioni. Super consigliato!"

Print goed en ziet er uitstekend uit. Uit de verpakking gehaald en gedroogd in Polydryer voordat ik het heb gebruikt. Ik heb een Bambu P1S. Instelling: Generic ASA. Shrinkage gemeten: X-as 99.44% en Y-as 99.56%. Gemiddelde shrinkage 99.50%.

Usando Imrpesora Bambulab P1S imprime perfecto con la configuracion basica del filamento que viene predefinida por la marca. Se gestiona como si fuera filamento Bambu y sin ningun problema. He impreso piezas pequeñas sin ningun problema y grandes he tenido que aplicar algo de laca en la base (sin laca el riesgo de despegarse es enorme) *VENTAJAS: - Buena adesion entre capas - Puedes usar los parametros standard de Bambulab - Calidad de impresion igual que si imprimes PLA *DESVENTAJAS - Huele bastante aun con filtros e impresora cerrada (olor similar al ABS) - El acabado es bastante brillante

Catastrophic bed adhesion. On a Voron 2.4 with textured PEI bed... I will stick to ABS

Lagre prints works best. Overhangs is a problem as many have mentioned. I would buy a diffrent asa next time