Omada 10G Base-T SFP+ to RJ45 Module, Universal Compatible(SM5310-T) | Hot-Pluggable, Support TX Disable DDM

Works with Ubiquiti Dream router 7. Does not run too hot. Plug and play. 3rd one I tried. Only one that worked.

Works great! Getting 10G to my UDM-PRO SE so I can use my full fiber internet speed!

I had previously written the review below. By default the SFP+ port is set for "set speed auto-module" which yields poor results as referenced. Changing the port config to "set speed 10000cr" makes the unit FAR more stable. It may not be quite as good as the $200+ Fortinet version, but it's staying stable and transferring at over 5Gbps with no packet loss, making this a great value. ----------------------------------------------- Network link drops for 15+ seconds multiple times per hour under light to moderate load (<200Mbps.) This happened with two separate modules, on two separate switches, using two separate 25' Cat6 network cables, and plugged into 2 separate NICs. I created an active LACP team and it's slightly more reliable, but still 2-3% packet loss, which isn't acceptable.

Works as advertised in a QNAP M3216R-8S8T switch. Had to do a simple reboot after the initial installation, and it's been fine since March of 2024. Unit is on 24/7. Gets close to rated speed and steady transfer of large backup images (30-68GB) on my 10GbE copper network with nvme ssds at each end. Insertion fit is easy, yet snug. Locks easily. Barely warm to the touch, not hot like many other SFP+ modules. Quite pleased with it... will purchase more as the network expands.

Works as intended in my TP-Link switches (SG3428XMP and SG3210X2) . Carries a 10GB connection over twisted pair cable. As this is the only 10GB copper module I've used, I'm not sure if all 10GB SFP+ modules get as hot as this on, but it gets almost too hot to touch. Time will tell how long the module lasts. Hoping it's a very long time as I have no way to run fiber optic cable in my walls. I'm stuck with the CAT5e that's in there. You can get a 10GB connection on CAT5e, but just on a short runs of cable. My total run is about 75 feet and I'm using CAT6A patch cables from the switch to the patch panel and from the wall jack in my office to the switch in my office. CAT5e in the walls, unfortunately.

Great way to turn an SFP slot into Ethernet...Works as described!

Working great for connecting a Ubiquiti UDM Pro to the Internet service provider’s 10Gb fiber modem. Speeds are as expected. Easy install, reasonable price, and quick delivery.

I needed this SFP+ transceiver for my TP-Link TL-SX3206HPP, which is an awesome PoE++ switch. The four RJ45 ports on that switch powered my WiFI 7 Ruckus R770 APs, and this SFP+ transceiver went into one of the two SPF+ ports on the switch. This worked perfectly to uplink at 10G to my Netgear M4300-16x switch. The SPF+ transceiver is only slightly warm, unlike others which can almost burn you. It works perfectly and highly recommended!

I think the market for 10GBase-T is a bit premature. I've tried several vendors of these SFP+ modules and when they work, they work for a short period of time and then dies. This particular device failed after 3 days of operation. When I removed the SFP from its cage, it was very hot and I was seeing several DDM log captures that the SFP was failing. Although interesting for use cases that have Cat6(a) already in place, I suggest avoiding 10GBase-T altogether. At least for now. And for those that are going to attempt to get 10G to their host devices on Cat6(a), these device add a bit of latency. Just sayin..... up to you to try but for me any 10GBase-T I try will be Enterprise grade only going forward. If I even want to revisit this.

In general the sfp+ works great, they are running a bit hot in my switch. My one has a low voltage warning (DDM) after contact tp support any divination of 20milivolt is fine. I am happy .

OTTIMO ADATTATORE, COMPLETAMENTE COMPATIBILE CON IL MIO ROUTER ASUS RT-BE88U ACQUISTATO SEMPRE SU AMAZON SECONDA MANO, TP-LINK UNA GARANZIA