CyberPower CP1500PFCRM2U PFC Sinewave UPS Battery Backup, 1500VA/1000W, 8 Outlets, AVR, Short Depth 2U Rackmount, UL Certified

Purchased this CyberPower unit about month ago. Have 2008 MacPro 8 core 3. GHZ fully loaded internally that was running for last couple years along with assorted Monitors-(2), printer etc. Had been using an APC 1500 & APC 1000- splitting various thing around plugged in to either one to share load. A MDD dual processor was in the mix but it was always on the opposite power supply, not both on one APC unit. For the last 3 yrs have been enduring endless stupidity with these APC power supplies. They would shut down randomly & repeatedly EVEN if the MacPro was not the one on that particular power UPS.Although for the most part - the UPS that was on the MacPro would shut down. You could switch a light on in another room- even a 1 bulb 75 watt could essentially trigger one of the 2 APC units to shut down as if they were overloaded. They were not. House is newer & wired correctly with 12 gauge/20 amp romex wire everywhere for any normal 110v outlets & 8 gauge 50 amp for 220v outlets & 200 amp service. The 2 power supplies are on their own line by themselves-nothing else. I am very familiar with house wiring & have rewired several homes I've owned. All wiring in house is up to snuff done properly.I tolerated this nonsense with these APC for years. They made absolutely no sense. I was aware at some point & positively as of recent reading that the 2008 MacPro's had PFC power supplies in them & that they would prefer pure sine wave power- as house current is. Even with that knowledge it still made no senses as to the random-regular weekly shutdown on the APC units with the computer asleep not even trying to wake or even having A TRUE power outage. The batteries checked out ALWAYS and if not hooked up to computer would work fine. If computer was awake & cut power they would hold system for as many minutes long as they were expected to. No problem. Just if asleep- turn light on anywhere in house- units sometimes/randomly cut out. If house current off & wake computers units shut down. Stupid really. Whats the point of the power supply ? (sounds like I am reviewing the APC's not CyberPower-right ?)Finally my MP had 8Gb of ram out of 16GB go bad. Had it replaced and I said that's it.I mean really- the APC power supplies were shutting down on a almost weekly basis & there wasn't even any power failures- the units themselves were THE power failures.Did as much research as possible regarding PFC power supplies & chose the CyberPower PFC 1500 unit. Cost more than the similar NON pure sine wave APC units. But cost quite a bit less than the Pure sine wave APC units. Who knows why APC charges so much for pure sine wave units. But after using their product probably for nearly 15 yrs- I was done.The CyberPower unit is a GREAT unit. Have read various reviews about the power switch(on unit-on/off & menu) etc problem some are having with it-I don't get the problem. It is a bit of a different technique how the button operates- but I picked it up quickly. The current power draw in numbers of watts as well as load capacity being used on the LCD display is great. You have real-time readout if you chose to, as to those numbers. It's like having Kill-A-Watt meter always on. You get to see the basic power fluctuations of your components. The unit is very compact- somewhat smaller than the APC 1500/1000 units.Right now connected with MacPro w/4 Hitachi 7200 rpm 64MB cache 3TB drives internal, ATI/Apple 5870 video card- w/3 24" monitors, epson 3800 printer, external OWC QX2 raid case w-4 hitachi 7200 rpm 32 MB cache 2TB drives & 2008 8 core MacPro booted off of that raid case along with MBP early 2011-17" plugged in but asleep, DSL modem, Dlink 8 port gigabit ethernet hub, 5th Gen AirPort extreme, MDD G/4 plugged in but off, the CyberPower shows a load of about 564 watts. That draw is confirmed accurate(slightly less actually for CyberPower unit itself not being in mix) if all were disconnected from CyberPower unit and plugged in- instead to the Kill-A=Watt meter. Everything asleep around 54 watts draw.I can switch ANY combination of light/appliance/central a/c /55" plasma/electric 220v clothes dryer/3.5HP 220v air compressor/ 5500watt electric heater- 500 gallon spa w/dual pumps etc in any combination on or off with computers asleep, awake, getting awake, going to sleep. UPS functions PERFECTLY & as expected- stellar performance. NO random shutdowns-nothing. Cut power to unit while computers asleep-no problem. You know the conclusion here -right?Pro's* Economical, compact, nice looking* PFC compatible- Pure Sine Wave unit.* Operates flawlessly* Cheaper than APC pure sine wave units* Power consumption/load LCD is very useful if you like that sort of thing-I do* 3yr warranty -same as APCCons* Cost more than NON PFC compatible/Pure Sine Wave units* CyberPower warranty/service- unknown quality yet. APC was/had excellent serviceConclusion.Highly recommended, especially if you have any of the MacPro's. I imagine some on PC side have units that are PFC and would require pure sine wave to operate a UPS on those computers properly also. I will not ever buy a UPS that is not a pure sine wave unit again.

CyberPower CP1500PFCLCD PFC SinewaveSo good, I bought 2! UPS systems in this class can easily cost more. I have had poor experience with APC systems in this range, so I gave CyberPower a shot. First one I bought for all my network equipment. I bought the optional network card as well. I have a couple routers attached, several WiFi Mesh base units attached by PoE router, laptop, NAS and a couple other items. I get 1 hour or more of uptime! (YMMV, yada yada) All the items I have attached amount to about 40% load if they are all on at the time.The 2nd UPS I bought about a year later for my home entertainment stuff - TV, stereo and a couple miscellaneous network items. Also gets about 1 hour uptime. No net card on the 2nd one, I wanted to test connecting it to HomeIt via HomeBridge and RPi.I don't need to manage these UPSs on a regular basis. We live in the mountains and power can be flaky. I wanted to have some way to monitor utility power when I was at work. The NIC adapter is perfect for that. I think it is a little on the $$ side, but has been worth it. Plugs right in and easy to configure. I started out with a 1 year promotional subscription to their service, but don't really need it. I still get power change notifications even without the subscription. When I get a power out notification I know I have about 1 hour of uptime before I need to turn on the generator. I did get the other CyberPower UPS to hook up pretty easily to my RPi unit running HomeBridge, with NUT UPS plugin. NUT can have a reasonably steep learning curve. I did get it working, but haven't really had the need to play with it too much since I still have the other UPS with the NIC. FWIW, I already had the RPi unit in place for a bunch of other IoT integrations with HomeKit - I would not go that route just for UPS management! ;PA word about generators:Most UPS systems will not play nicely with your standard portable open frame generator, regardless of how large/stable it is. It's the shape of the stepped wave that can often fool the UPS causing it to trip on. The only foolproof way around that is to 1) Get an online UPS system at 3-5 times the cost of line-interactive 2) get an inverter generator. Don't get too fooled by 'generator' modes on line-interactive or standby UPS types. Those modes may help, but in my experience it will not work 100% of the time. Initially I had a standard Champion 7kw open frame delivering power to whole house. Performance was rock solid voltage and frequency delivery without fluctuation. These CyberPower systems worked off the generator about 75% of the time, tripping on the rest of the time. I have a couple APC systems with 'generator' mode that would have nothing to do with the generator - they would trip instantly even in 'generator' mode. Still, this was not stable enough for me. My solution was to get the inverter generator - a 9kw Westinghouse delivering power to the whole house. It was actually cheaper than getting an online UPS equivalent to this CyberPower! Ultimately it wasn't just the lower cost, but the versatility and stability of delivering super clean pure sine to the whole house. Better for everything inside. Zero issues, of course, with these CyberPwoer UPSs. They just see the generator output as regular utility power.

The CyberPower CP1500PFCLCD is an excellent UPS that provides reliable backup power and strong protection for PCs, gaming setups, and home office equipment. It’s a must-have if you want to protect your devices from power outages and voltage fluctuations.One of its biggest strengths is the pure sine wave output, which makes it fully compatible with modern power supplies, especially those with active PFC. With a capacity of 1500VA / 1000W, it can easily handle a full PC setup, including a gaming rig and monitor.

I ordered this UPS because I wanted one for my custom built PC and its peripherals. Fortunately, I found the 900W/1500VA when it was a lightning deal and ordered it immediately to take advantage of the savings. The first thing I noticed when it was delivered was that it was much heavier than it looks, it made sense though since this is essentially a car battery (lead-acid) in a different form. The second thing I noticed after I opened it was that it had a strong smell to it, after I plugged it in the smell went away after about a day. The smell only comes back when the UPS switches to battery mode and the internal fan goes on. I think that it may go away if I left it on battery mode for a while but I have not gotten to testing it yet.The sticker says to charge it for 8 hours before use to fully charge it but mine was about 80% charged when I received it and plugged it in. In order to turn it on, you have to hold the power button (instead of just pressing it) and then let off after 1 short beep. In order to turn it off you have to do the same process but it instead of letting off after 1 beep, you let off after 2 short beeps.There is an LCD screen on the front of the unit and the top half shows constant information about the battery capacity, load, and whether it is connected to the outlet or running on battery power. There are 10 information displays that you can cycle through on the bottom half:1. Input Voltage2. Output Voltage3. Output Frequency4. Output Power in Watts5. Output Power in Volt-Amperes6. Output Power in Percent Watts to Maximum Wattage7. Output Power in Percent VA to Maximum VA8. Battery Charge in Percent9. Estimated Run Time in Minutes10. Number of Events (Times switched to Battery Power)The included manual states the other button functions such as next, previous, keep display on, etc.There are 12 total outlets, 2 front USB ports for charging, 5 for surge protection and another 5 for surge protection with backup battery power. There is a input and output for coax and ethernet cables and an output for USB B and Serial connector. The unit comes with a USB B male to A male cable, a coax cable, and telephone cable as well.I don’t use the coax cable but I do use the ethernet input and output, as far as I’ve noticed it doesn’t slow down the connection at all and it feels like the UPS isn’t even there. I also use the USB connection to plug into my computer and use the PowerPanel software I downloaded from CyberPower’s website to monitor the UPS from my computer desktop.I found that the software isn’t as accurate as the LCD screen on the UPS itself but there are some extras found in the application that isn’t on the unit. These extras include but aren’t limited to:1. The ability to set the sensitivity to low, medium, or high so that you can choose what the difference in voltage relative to the AC outlet is for the unit to switch to battery power2. Setting whether to keep the computer on as long as possible (i.e. run until 5 minutes left on battery) or to conserve the battery life of UPS (i.e. run for 5 minutes on battery).3. Being able to schedule when to turn on and turn off the computer at an exact day and approximate time.I currently have my desktop and monitor connected to it and the estimated running time at full load on both is about 15 minutes which is more than enough time to properly shut down my machine. I may have to set the sensitivity lower because it switches to battery power whenever the clothes dryer is initiated but everything else works fine. I do not have an oscilloscope so I can’t comment on the sine wave output but from the other pictures posted it looks and functions fine for my use. It features Active Power Factor Correction and that works well with my power supply as well. Overall, this is an excellent UPS and I would recommend it to anyone who needs backup battery power for sensitive devices, just be aware of the initial smell that comes with the unit and you will be satisfied.

I have used this UPS brand many years and it has exceeded my expectations. Quickly turning over to battery and keeping my internet connection and WiFi stable, it works with all my devices and completely maintenance free. Remains relatively cool and has been a great resource during storms and power outages.

Update: This UPS does NOT mount flush with the rack rails, unlike every other rack-mounted equipment I have seen in decades of working in computer centers! The ears are not flush with the front of the UPS, but are set back about 2/3 of an inch. This makes the UPS protrude more than all the other components in my cabinet and mars the aesthetics.Spouse wanted a horizontal orientation on the UPS we use for our media component. This fits the bill perfectly. We are very satisfied so far. We have it connected via local USB to our media server PC, and it's supposed to methodically shut the PC down when we lose power. This has been successfully tested during a power outage.A few caveats:- I'm not a big fan of the not too intuitive Windows-based monitoring software, but it "usually" works. I had to uninstall, remove drivers, reinstall, reboot a few times, though. It keeps asking me to enter the battery purchase date, but offers no way to do so. I tried installing the "management" software in accordance with Internet advice, but that didn't function AND broke the monitoring software...- I did not add the optional network card (over $300?)- I did not pay for the optional subscription to their cloud-based monitoring service.For a 15 amp circuit and/or rack mounting this is a great option, subject to the above caveats.

I got this for my audiophile stereo system, satellite tv receiver, and 65” tv. It works great. No noise at all on the stereo, even on phono and am radio. It arrived showing 100% charged. I had everything on, pulled the plug, and everything kept running with no glitches. Showed 30-45min of battery runtime depending on TV content. I onl ran it a couple minutes on battery. This home entertainment system does not like brief power interruptions and this backup power supply is just what I wanted.

[update 10/1/24] We have 4 of these cyberpower sine wave units, and 3 APC units. They are still going strong, except one, the rest still last long enough to save and shutdown safely. The only issue is that when they fully die, they do not turn back on automatically, you have to push the power button which is REALLY stupid on a product like this. The good thing is, they shut the computer down when the battery is at 20%, and the last 20% will last so long the UPC almost never turns off. But when the battery goes bad, then you have the issue of the computer not being able to turn on the next morning because the UPS is off from the storm night before. I wish I could say which one lasts longer, APC or Cyberpower, but I can't tell the difference. I think I'll buy whatever is cheaper. You can buy generic 12v 9ah batteries and change them out when needed, so battery life is not really a selling point IMO. I wonder if you can buy a lower wattage and upgrade the battery amp hours? I only need like 600 watts.[update 8/21/18] I'm back to buy another one for another office computer. The 2 I have currently have kicked in about 3-5 times when the power blinked, and once the power was out for almost a whole minute. Again, no issues.[orginal] So far so good. I was worried about the smell other's talked about. I bought 2, and when I pulled them out of the box they smelled pretty bad. I immediately took all of the plastic off in hopes that the smell would dissipate faster with the plastic off. I let both of them charge last night in my office, and this morning there was no smell. So whatever the issue was, I think it was resolved. With 2 of them and my office does not have very good ventilation, I think I'd smell it if it was a serious problem. I know my ventilation isn't great because I remember my printer smelling bad for about 2 days.I tested the battery backup. I unplugged with my computer running. For context: I have 3 monitors, a small 2.1 speaker system, and my 1-year-old desktop tower plugged into it (with wireless keyboard/mouse). So I'm using 5 out of the 6 plugs. It says I'm pulling 153 watts, and that I should last between 47-53 minutes. The display says that that input is 119volts. When I cut the power, my monitors did not even blink. The UPS beeped like it should, and the display switched to telling me how many minutes I had left. it bounced around a little, I assume my computer pulls varying rates of power. It leveled out at 53 minutes. I did not wait to see how it shuts the computer down after 5 minutes of being on power. I was also surprised that I did not see any notification on my computer monitor, it was just an audible beep. My computer is very quiet, so I could hear the UPS start to hum, but it was around the volume of a normal computer starting up. The hum was a little reassuring that it was working.I will update this if I have any issues.

I needed a rackmount UPS for my home lab. This one is a great value for a 1500VA UPS in such a small form factor, and it runs my server for nearly an hour without power, fantastic!

Great UPS unit. I was powering 3 R710s and a DL380 GEN 9 with this. It had no problem and would give them just enough time to shutdown in the event of a power outage.

I'd been in need of a whole new UPS, as my smaller 350W ones from 2008 were now no longer charging batteries and would drop the second any type of power issue was detected so grabbing this as its then price of $400 for a 1500VA 1000W UPS was far too good to pass over. I have a 1500VA, 1500W CyberPower UPS for my homelab's rack, so I'm already a heavy fan of CyberPower.Pro's: The unit isn't too heavy and it's shallow depth makes it ideal for limited space in a rackmount, and it doesn't bend the rack up. Ironically, my managed switch puts more of a wow in the rack posts than this unit does. o.OUser interface is generic, simple and easy-to-use. If you've used any UPS before then there's really no need to worry about display settings and how-to's.It's got the new built-in green energy system that when the UPS is charged and not on battery, it auto-bypasses the transformer and reduces energy consumption and waste by 75%.Unit switches over from utility to battery quickly, quietly and returns to normal just the same.NO LOUD FANS! In fact, I didn't even notice let alone hear if there was even fans in this unit which is very nice! So bonus on it being ultra quiet!Came to me with 92% full charge, so not a lot of time needed to fully charge it before putting it into production.And last but most important of all: She has that beautiful and wonderful strong fresh/new electronics smell one can't help but admire and relish. That alone was worth the $400 ;)Cons: Unit says default setting is MUTE when running on battery. They lie! ;) Easy fix, though!The screws for the rackmount holes were too small for the back bolts on my rack, and I had to use the screws that came with my rack. You may have different results depending on your rack.

I deal with Enterprise Data Centers, but for my home lab I wanted something more affordable so so thought I'd try Cyberpower. I'm glad I did.This unit effortlessly provides full power as advertised, as well or better than other UPS I've used. Highly recommended.

We have these at work in crappy conditions with even more crappy power and they are abused.... never failed. I bought one for myself. If you can't afford some monstrosity from APC these are you next best bet for like half the price.