1 Pole 40 AMP Heavy Duty Enclosed AC Contactor

Great product that worked out fine as a replacement. I was sure to disconnect the power and discharge the capacitor. I took a picture of the connections before disconnecting and removing the old contractor. The markings on the terminals of the old and new part were completely different. I was just careful to connect the primary power to the side labeled 440v and the control wires to the side labeled 24v. The main control wires on my AC unit had terminals whereas this new part had screw connections for the control wires just like the high voltage side. I had to cut the terminals off, strip the wires and insert them into the holes and tighten the screws. On my unit all the yellow control wires went on the right. I then had to connect all the terminals properly on the right, left and top. One of the terminals was rusted and broke off. Luckily I had a terminal and crimper for it. Everything went back together great and once I closed everything up and reconnected the power the air conditioner worked fine. Pretty easy for what the AC repair company wanted to charge me over $500.

Ordered early one morning and received it early the next morning, made it nice to fix my A/C for a 100 degree day. Perfect replacement for the original one and works great, 15 minutes to install. Thank you Amazon.

I have a 3-ton Amana A/C unit that is 23 years old. Over the past few weeks, I was aware of the HVAC system being Off, but that the compressor outside was still running, building frost on the cold side line. At first I just went to the Breaker Box and shut off the A/C breakers. Then I took the side cover off the A/C unit outside and "rapped" on the contactor. After 2 or 3 hits, the compressor shut off. In my case, the contactor was working well enough to turn On the unit, but the contacts would weld themselves tight together and not allow the unit to turn Off. This unfortunately caused many nights of poor sleep as I never knew when the next time the contactor would fail "On" again. As you are already aware, Amazon carries an exorbitant collection of contactors from which to choose, but I drilled my decision down to this Protactor contactor. In case you don't already know, basically all of these contactors are built with the same footprint and size, with the main differences being the coil operating voltage (24, 120, or 220VAC), the contactor (relay) contact ratings (from 25 to 40 Amp), and the number of poles that are required for the control circuit (1, 2, or 3). My contactor was a simple 1 pole circuit with a 24v coil and contacts rated @ 25 Amps for FLA (Full Load Amps). Therefore, if I can upgrade to a 40 Amp FLA contactor, it allows the contacts to live a much longer life with 60% greater contact area. I received this 40A Protactor within 2-days after ordering it and installed it right away. My A/C compressor and fan are now running better than ever! I really mean it! Before, with the worn out original contactor, the compressor used to literally groan and growl especially during the first few minutes of operating. Now, with the 40A Protactor in place, there is none of that, very smooth and quiet, as it should be. I thought I might need a new compressor, but now I realize that the old contactor was wasting energy across the contacts and not allow full voltage and current to the compressor unit. The A/C appears to also be running less in duration and less often, due to improved operation efficiency. My family is delighted and impressed that I was able to repair our A/C system with a part that cost less than $21 w/ Tax. Now no more worries about the contactor sticking in the On position! I totally recommend this contactor for anyone in a similar situation. It is worth its weight in gold!

Installed a few days ago, works great. If your contactor terminals are labeled T1/T3 and L1/L3, plug everything in exactly how the original was plugged in. Most replacements are labeled T1/T2 and L1/L2. Use T2 and L2 in the same way you would have used T3 and L3, they are the same.

When working on something that runs on 240VAC it's really important to do things safely. Turn Off the breakers to the compressor and the inside unit before doing anything. This fixed my AC problem. Couple weeks ago during a late night storm my AC quit working. Or at least the compressor wouldn't come on. Inside unit seemed to be Ok. The compressor unit is about 8-9 years old, so I at first figured it was the starting capacitor - changed it out for a new one - no luck. There was a possibility that the low-voltage wiring might be the problem - its about four decades old. Check it - it was good. So I ordered a new contractor unit, based on the model/part number of the old one - which has been discontinued. The new one didn't look anything like the old one. It was actually a two-pole one instead of a single-pole. So I ordered one of these - based on appearance and specifications. Took about a half hour to install. Flipped back On the breakers - crossed my fingers and turned on my AC. Compressor chugged to life and cool air commensed to blow. Yea! One hitch in all of this. The label on the new piece shows the wiring mirrored to what my old part shows. So I had to make a decision - flip the wiring or hook it up like the old part. Tough decision. I went with doing it the way the old one was wired. And that seems to worked Ok. Side note. Looking at the old part - there is a little cover on the front. Opening that up you can see the relay contacts. Both contacts were heavily carbonized. My guess is I could have simply cleaned those contact points up a bit and gotten a few more years out of it. But still, for the price a whole new part is better than an almost ten year old one. I'm happy with my purchase. Including a photo of my old part with the mirrored wiring.

I replaced my AC's contractor in 2019 with this model, and it did work great until 2025. I just bought the same model, 2 of them this time so I have a spare on hand, to get back working. I will update based on the new one's performance, but the old one did only last 6 years. This is in line with other lower star reviews, and the failure mode was the coil. You can depress the test button and it conducts fine, but applying voltage to the switching coil does not activate it. I put a multimeter on the old one and my spare, the old/burned out one measures 0.9ohms on across the coil and the new one just over 14 ohms, so it clearly shorted out over time. It is either an environmental or a duty cycle issue, but at the cost I'm willing to deal with it if we are talking once or twice a decade...it keeps my old AC unit kicking.

This fits the most models and easy install

Worked great on old Lennox condensing unit!