Grafix Adhesive Backed Inkjet Film, Clear, 8.5 x 11 in, Pack of 6

I use this product for custom foils for card games. Be aware that adhesive isn't totally clear. Attached is a comparison of this product (left) vs. a laser printed foil attached with glue (right); as observable, this product produces much more vibrant colors with better, clearer foiling. It's not completely clear, and it won't pass cursory inspection, but it's the best film for foiling. Be aware that, depending on your climate, you may have to let it dry for much longer than I did (i gave it about 10-15 minutes). The adhesive is strong and sticks; I just wish it was slightly cheaper, as 70 smackaroos for 50 pages is rough. Use a boxknife or a razor knife to separate the adhesive carefully from the backing. Printed with an HP Envy 5055.

Just an awesome product. Bought this to do wording for my 3d printer business. This paper has allowed me to one up some of my competitors. My only complaint would be it is thick. I would love it a few mils thinner but other wise works great. Drytime is not an issue. Print on it, put it on a self for 10 minutes and dont touch it. Worked great from the first print. I am using a cheap hp ink jet so nothing special on my end to make it work. Will be ordering more. As a side note - If you are using it to make a sticker for a dark background light colors like yellow will not show up. The ink is translucent. Make sure you print bold and in a good font to contrast your surface you are sticking it to.

If you are looking for clear this is clear. It's not frosty like avery labels. However, my inkjet ink took over 1 day to dry and even then, you can rub it off with your finger, applying pressure. The ink beaded pretty badly until I changed some settings for the paper style on my computer, too, and slowed the print speed. The label is really thick/sturdy. It didn't bubble or streak nearly as badly as avery. But when you are applying pre-made stuff like this, you will always have a little bit of adhesive bubble pockets (which you can try to press out for the most part). Like other reviewers mention, it is hard to peel - you have to get your finger nail under the corner edge and pull towards the glossy side, lifting the gloss off the paper (it's hard to do it the other way, trying to peel the paper off the gloss). If you need a really thick, really clear label, and have patience to peel, and let dry, this is good stuff. I found a product similar to this that I like better called clear gloss laserinkjet labels (no drying or peeling issues, still nice and clear). Hope this review helps. It is hard to find descent clear labels.

Nice clear printable paper. It is a bit thicker than I was expecting. Which actually ended up working out based on the project I was using it for. The inject prints out a very nice image onto this. However, you absolutely will have to put some form of clear coat or laminate on it or the ink will rub off or run. I used an acrylic spray. As I mentioned, this is thicker material. So not for use on something that you need bend-ability or flexibility on. And because of the thickness, the outer edge of where you cut out will be noticeable wherever you stick this down.

I purchased this for use in Pinewood Derby cars. The paper worked well and printed clearly on my HP Inkjet printer. The film is quite thin and is translucent. It stuck very well to the cars. Others have mentioned a lack of clarity. I did not find that and was happy with it. One word of warning is that it takes a while to dry after printing. I touched it too soon afterwards and some of the graphics smudged. I would recommend that you give it 12-24 hours prior to aggressively handling the printed output.

this adhesive film works great for what I use it for. I bought this because I make my own decals for RC aircraft. I have no problems using this with my canon inkjet printer the ink drys fairly quick 5 min or so not a big deal for me and does not smear. I might have to see if I can set printer to put down less ink just to see how that works. the only problems is that its hard to remove the backing the easiest way is to take two pieces of tape and put on both sides on the corners of paper and pull apart. works like a charm I will buy this again.

This is a fantastic product for making titles and graphics for your scrapbook. It allows the background to show as if the title is floating on the page. The adhesive makes it easy to adhere to the page. By using the landscape feature you can create titles that go across 12 x 12 paper. I would definitely purchase this product again and highly recommend it. I also bought Wausau Papers Astrobrights Print and Stick which has a matte finish and adhesive back on a bright white paper for titles and graphics.

this is still a good product, but the paper that I've been getting recently isn't 8.5 by 11 anymore, its thinner and messes up my prints sometimes, I'm not sure if its just a freak few accidents where the paper was cut poorly or if this is just their new standard, regardless it is very annoying. Also the coating on the top of the paper seems to have changed and my prints are starting to splotch and the colors are dulling quite a bit, its also curling more than it used to. I will try to purchase it one more time but if the quality truly has gone this down hill then I'm finding an alternative sadly.

Awesome product.did what it said it would do .printed nice color dried fast and applied super easy. Great product .pricey but worth it .

El papel de buena calidad

I love these, I use them to make altered art foil MTG cards for EDH decks. Saves you a butt load of money and most times they look better than the real thing

Really nice quality was impressed. In the beginning, I thought my printer (HP Office Jet) wouldn't pick the paper, but everything went fine.

Bien buena calidad