Lead Sled DFT Rifle Shooting Rest with Adjustable Ambidextrous Frame for Recoil Reduction, Sight in, Range and Stability

I got this in early last week, put it together and took it to the range the next day. I timed myself for assembly - 43 minutes including unwrapping the parts. And I lost about 5 minutes looking for the screw that holds the front cradle down on the ram. Obviously the #!!@# who packaged this left it out but fortunately I have 6 mm screws in my shop to finish the job. So as I prepared to check to make sure my screw was the right size and length, I realized the "missing" screw was already threaded into the ram. Take it out, put on the cradle and screw it back down. My sincere apologies to the fine person who packed this. All the parts were there. Assemble was easy. Run the ram all the way to the top to fasten the top part of the front cradle to give yourself room to work. Getting those screws started can be a little tricky, Use one of the included hex wrenches or a screw driver to hold the clamp down till you get the screws threaded and it's easy enough. I turned the rest over on it's side when finishing up this step. How does it work? Very well. In fact I had already used another one at the range a few weeks back while helping someone sight in his rifle. I guess that really pushed me into going ahead and buying one. The Lead Sled it fairly heavy and I was checking the sight in of an old (and unfortunately now obsolete) .225 Winchester at 200 and 300 yards, It's a low recoiling rifle and I didn't use additional weights and probably won't for heavier rifles either. I found the adjustments easy and fine with no backlash. I did generally have to reset it somewhat between shots but I've never used a bench rest that didn't require some readjustment between shots. It was very easy to precisely set the crosshairs on the target and the crosshairs stayed in place as I got into final shooting position. After a bit of tweaking the sight in at 200 yds I was able to hit a 4 inch gong at 300 meters (330 yds) with my last two shots so it will hold the rife steady. I did not have any wobble in the front cradle even when elevated. The Caldwell site addresses this saying they have corrected that problem with earlier ones. When I first assembled it I did notice that I had to gently push the ram down when near the bottom but when I had the weight of a rifle in it, I did not have that problem. I did lubricate it and had no problems at all when I took it to the range even without a rife in it, There is a thick recoil absorbing pad in the rear cradle and that effectively makes for a much longer length of pull and I had trouble getting my eye close enough to get a full image in this scope. That pad is not removable. And last I put my rifle in it to clean it. The way it's made, all my rifles are secure in it, not true in other rests I have/had. That's one of the reasons I bought it - not a lot more expensive than some of the plastic vises on the market. I didn't bother with the rubber hold down strap. I expect most will find it of little use. All my rifles, including varmint rifles with broad, flat forends, set below the top of the front cradle so the strap would be above the rifle. I hold the rifle down with my left hand with any bench rest. Yeah it's made in China but it is all steel and is well made. The ability to adjust the distance between the front and back cradles is another reason I bought it.

SCORE 57% off!!! I am very excited to properly sight in my hunting rifle. I have used these before - but they were borrowed. This one is MINE. This unit is very sturdy, and stable. It will work fine for sighting in. . I like the split rail design, it allows for extended magazines/handgrips. Pro Assembly Hint: Before screwing in the four M5 screws into the Front cradle assembly, turn the Elevation Wheel and raise the Windage Cradle Sub Assembly to the fullest extent, that way, you can put the long end of the allen wrench into the M5 Cap Screw, allowing you to turn them 360 degrees for easier assembly. Also, I tossed some grease onto the bearing/race just because...

The Caldwell Lead Sled DFT2 shooting rest has a reputation as one of the best in the industry outside of high end bench competition rests. This reputation is well deserved. From my .22lr to my 30-06 it provides a stable, easily adjustable, rest for 100 -1000 yards. IF I was a serious competition shooter, I might go for a higher dollar sled, or perhaps build something myself, but for the average hunter or recreational shooter, it is an excellent choice. While the Sled has an adjustable rear foot that aids with adjusting elevation, my one complaint is that the front feet are fixed, so the sled can not really be adjusted for cant correction if your shooting table is not perfect, but it is not really designed to lock the gun in a single spot like a competition bench sled does. You can still twist the gun in the sled sufficiently to compensate without the gun being so loose as to slip off target during the shot. Still despite this, I stand by my statement that it is one of the best in the industry. That said, the frame can support AR platform rifles or similar, or an HK 91with a 20 round magazine. Both fit without problem, BUT magazines could not be reloaded with the rifle in the sled due to the frame. Neither I, nor any of my shooting buddies have extended magazine bolt action rifles, but I would imagine anything longer than 4 inches below the stock will likewise fit but not be able to change magazines while in the sled. The newer Lead Sled 3, to the best of my knowledge, is not able to be used with long magazines due to the center frame bar. Needless to say a .50bmg Barrett 82 will not fit in the sled :) It may be able to hold some of the larger rifles, it is not really designed for bulky or long precision shooting rifles, but if that is the type of shooting you do regularly, I would wager you have a higher end sled anyway.

I can not get a cheek weld with this rest. That makes it almost impossible to zero accurately. Maybe I can cut that tall rear stock holder down? But it's taller than any of my current stocks. Going to try a different shooting table before I modify it. A couple of wedges on the sides of that rear holder makes a stable hold and repeatable shots, but I find myself behind it trying to center the scope for parallax. Stout, adjustable where it needs adjustment. the front holder is a softer plastic, almost rubber like. It shouldn't hurt the finish on your favorite rifle. Comparing to my old Champion bench rest with the grip rest right under my trigger hand, the Champion is still more comfortable, easy to get a cheek weld, but not as positively repeatable or stable as the Caldwell. A little weight, a steady trigger pull, and it could be a .5 MOA rest all day

Usato con frequenza al tiro a segno , prodotto caro ma di ottima qualità.

Ideal zum Einschießen! Würde es trotzdem Preis noch mal kaufen!

Funciona muy bien. Es bastante pesado.

射撃場でスコープ合わせの時に重宝します。 ただ、砂袋を乗せてもサボットだとリコイルが強くて大幅にズレるので、何度も修正が必要にはなりますが、正確にズレを修正するのに最適です。 アメリカ製で、輸送中なのか、元々弱いのかは分かりませんが、塗装が雑で剥げてるところや傷も多々あり、完璧を求める人にはがっかりしてしまうかもしれません。 飾り物ではなく使ってなんぼという人には素晴らしいアイテムだと思います。

C’est du costaud !! C’est lourd, c’est solide, c’est stable. C’est ce qu’il faut pour régler sa lunette de manière optimale. C’est pas donné mais c’est qualitatif.