VViViD XPO Black Carbon Fiber Car Wrap Vinyl Roll Featuring Air Release Technology (2ft x 5ft)

This was my first time wrapping a car panel, and I chose to start with my hood, which is a pretty large area. It was definitely challenging on the first attempt. I ran into some wrinkles, and the vinyl adhered very well, making it difficult to lift and reposition in certain spots. However, with some patience and the help of a heat gun, I was able to smooth out the wrinkles and make repairs much easier than expected. Overall, the vinyl was forgiving enough for a beginner, and the finished result turned out great.

I purchased the VVIVID XPO Vinyl to wrap the trunk of my 2015 WRX. Overall I was very pleased with the item. I am inclined to think most of my problems came from user error other then product failure. That being said, Below is my breakdown based on what I was looking for in the product;Packaging/Shipping: The vinyl came within two days in a full roll. I know there were some concerns for the sheet coming folded. This was not the case and the roll was crease-less. Open the box for the first time outdoors however. The bottled up vinyl smell is a bit strong when the product is first opened up.Product Quality: My first thought was "Wow this is more stiff then I expected". Most of this stiffness is due to the backing paper. The carbon fiber is more of a raw texture giving it a matte finish. It still has a great look, just not as glossy as real carbon fiber parts. This is all a look preference though. I think it looks better with less gloss.Ease of Use/Installation: This is a mixed bag for me. If one has a smooth, semi flat to flat surface, then installation is a breeze. I started on the top of my trunk and that was a quick as anything to install. The vinyl is super forgiving and very easy to push bubbles through. My trouble come with the turn down to the back side of the trunk. The vinyl is nice in that it is heat activated. This allows one to pull up and re-position many times with no issues. I had to pull up and place the back a few times and one of them used too much force. This resulted in a tear in the vinyl. At this point I had to scrap the back of the trunk and just do the top. Like I said, this tear was most likely my own error. Overall, I thought it was very easy to use if one is patient with it.Durability: The installation was about 4 weeks ago and the product is holding up just like the day I installed it. Some bubbles will appear days after the install as it is baking in the sun. All one needs to do is rub them and the air release tech will do the rest.Overall: Really great product. I actually plan on purchasing more to wrap my roof and hood. Looks great from any angle. I have had a few people ask about it already because it looks so good. Five stars based on the fact that I was a complete beginner and was still able to do a professional looking job. Great for first time users of vinyl wrap!

High quality carbon fiber wrap, VViViD is some of the best vinyl out there, but this stuff is VERY thick. The pattern is a physical texture on the vinyl itself which makes it really difficult to stretch, even under heat. I made the mistake of using this to learn how to wrap with on my interior to do some silver plastic delete and it has been INCREDIBLY difficult to work with.However! The results look and feel FANTASTIC if you can be patient. Get ready to work on each piece for at LEAST an hour, if not more. Some pieces took multiple hours and multiple attempts and even on the second attempt it's still not right. Buy 2x the amount you plan to use because you're going to absolutely tear this stuff and throw a lot of failed attempts out. It also has some issues adhering (on very thin areas, because it's so stiff).The top two corners in my center console job shown below eventually bubbled back up and tore (and this was the second attempt).

VVIVID® XPO Black Carbon Fiber Car Wrap Vinyl : My first time trying anything like this. I bought a set of applicators, two with felt, for under $5. I flattened the vinyl using a heat gun, peeled the backer off and applied the plywood. Then flipped over and folded the sides. I am using it to cover 3 boards to cover an open top shoe rack. I can't say I did a great job around the sides or corners but it looks good. It smells so I put it outside. Hopefully it doesn't get too cold. It will likely take a few days or longer to air out. I could put it in a bathroom with the fan on.

Great product. It's lays good. Easy to work with. Will buy again

Material was easy to work with. You will definitely need a heat gun for corners and edges. It definitely looks good and was plenty of material to work with.

Sticks and goes on well just came with wrinkles and a few areas were damaged before I even used it and took it out the package takes a while to put on if your learning corners feel impossible even with a heater to make it stretch it just doesn’t turn out that good it’s a good woven texture and looks good from afar and close it’s not too thick but any curves ur gona need to heat it up

First, great quality vinyl wrap. Length was 5ft and width was 1ft as stated. However I did measure in a few places for width and found there to be a slight variation. Bit this was about 1/8 of an inch over the 5ft span. The vinyl cut easily with a razor knife and adhesion is good without adding adhesive. Now for installation; I bought this because we have had extremely hot days that caused my vent air freshener to drip down the dash. The chemical and heat are through the finish of the radio control panel and trim. Thoroughly cleaned all surfaces with rubbing alcohol. Also note I removed all trim pieces and stereo control panel for this install. I have watched several videos of this being applied without removing the trim, but the end results didn’t look desirable around the edges. And all of these did not have a navigation screen. Most videos state to cut in corners to apply without creasing. Then I watched a video of professionals applying to the outside of vehicles. They heat the vinyl and slightly stretch then push out creases and bubbles. I used a $16 genesis two temperature heat gun also purchased on amazon. Using a heat gun made the install extremely easy and forgiving. In addition this also made the adhesive set up and harden faster. Using this method allowed for a tight comforming fit on the trim pieces. In addition by matching the pattern the heat allowed for better seams. The heat allowed easy manipulation by hand with no vinyl tools required. All trim tools I purchased from harbor freight as the entire kit was only 7.99. And a .99cent razor knife. I used the trim tools to push in any pieces the dislocated after reinstall of trim. The wrap did not prevent trim pieces to fail to install and no damage occurred to the trim in the process.

No es la primera vez que lo compro muy recomendable aún para amateurs como yo

جالي مقطوع بطريقه معفنهوطوله ٤٠ سنتيمتر في نص متر

This stuff does not stick at all like it should, maybe its too hot this summer, but its become useless unless I guess if you buy glue to add, but its supposed to be ok without, which is NOT!

This Black 3D Carbon Fiber Vinyl Wrap was very good and easy to use! A heat gun is a must if you are wrapping non-flat surfaces and edges. I used this on my car to wrap the shiny center console. This vinyl was very easily screeched when the heat gun was applied to it and shrunk very well when heat was applied. the texture is super nice and is not a fingerprint magnet. Very happy overall. love this product and would buy more in the future.

Ohhh how i love this product!!! Takes some patience and practice to install but im so satisfied with the final result! I put it on my trims inside my car, my car was in the sun windows up in hight summer temperatures, in the coldest winter temperatures and it still looks amazing and didnt peel off or make air bubbles. Very good quality