ASOKO Under Desk Light, 16Inch Dimmable LED Under Cabinet Lighting, USB Plug in Cabinet Light for Kitchen/Shelf/Workbench/Cupboard, 3000K/4000K/6000K

My wife needed a bright light for her pull-out shelf keyboard. With adjustable brightness and warmth and an on-off switch instead of motion detection, at a reasonable price, this seemed like the right product. . . and it was. The distances between the lamp and the switch and the switch and the power source were perfect. The switch includes buttons for warmth color and brightness and a larger on-off switch. I and my wife particularly like that once you make the settings they remain the same for the on-off switch -- no cycling through a single button to get to your desired setting each time. This is a sign of good engineering and good quality. After I installed my wife's light I purchased and installed one for myself. Ditto review for that one. I can't say whether or not the two sided stick-ons were adequate since I used 3-M mounting squares trimmed to cover the entire back of each lamp and switch in a bit of overkill. The point being, don't throw a one-star review if the stick-ons provided don't secure the light to your satisfaction, when 3M makes 2-sided tape and mounting squares that will well-solve that little problem. Just use isopropyl alcohol to pre-clean all surfaces. We are both happy with this light.

I actually really LOVE this little light, it's EXACTLY the kind of thing I was looking for.I needed a little bar light to go underneath the cabinets above my monitors, something unobtrusive, and this really fits the bill.The fact that it is removable and portable is a nice little feature, though I doubt I'll use that feature for my current needs.The three different light colors/warmths, AND the fact that it is dimmable to a great extent are PERFECT for my needs. I needed light directly on my workspace and in front of my monitors, bright enough to light my desk specifically in an otherwise light room, but I also occasionally like to work at night, and don't like to advertise the fact that I'm here, and this little light is perfect to light my workspace without shedding a lot of light elsewhere. I can now work in the dark, yet still see what I'm doing, and dim the light to whatever level I need.The switch being about a third of the way down the cord is also perfect. I've attached it to the sidewall of my desk with the included clip (used the other one to clip the cord out of the way down the outside of the desk). I appreciate that it is NOT on the light bar itself - it's out of the way, but within reach, and I'm not constantly fiddling with the light bar, potentially causing problems with its placement or attachments. The cord is the perfect length for the light bar to be centered over my workspace, and the cord to drape behind the monitors, down the side of the desk, and wrap around to the front of my computer tower to plug into a USB port. (If I wanted to use the included wall plug, it might have *just* been long enough - but I might also have wanted an extension cord of sorts.)The two different styles of magnetic 'clips' are a great idea - you can use and place it in a variety of angles or configurations quite easily. I only needed the L-clips, but if I were using it strictly on a flat surface, the discs could be useful.The one caveat is that, yeah, the 3M adhesive foam bits are pretty crap. The first one, when I pulled off the backing, the actual sticky part came with it - so it was clear that piece was going to fail. The other one failed an hour later as well, and that was after leaving the adhesive to adhere without the weight of the bar for that hour. (And the bar itself is quite lightweight.) So - find yourself a different, better adhesive, and you'll be set. Probably either some genuine 3M Command strips, or those Command 'plastic velcro' bits, if you want something that's easily stickable/removable.I simply used a couple of strips of heavyweight Scotch "book tape" that I had laying around and I know to be very sticky to strap the L-clips to the backside of the cabinet edge - it's functional, and can't be seen.One more thing - it wasn't immediately obvious to me where the actual 'magnets' are in the strip. They are located ONLY at the ENDS of the light bar. Attach the magnets, THEN whatever you're using to stick the metal pieces to your location, and either mark the ends, or position the whole thing in place.

The unit is small. That's either good or bad depending on your needs. I have it under a shelf where I am writing below on the attached desk. One was not enough to create even lighting across the medium size desk. So I had to buy a second. There is a bunch of incremental brightness from nightlight to working light. Very nice. 3 different colors which seem to simulate hard, soft, and yellow temperatures. The magnets work well to support itself HOWEVER (and this may be more about 3M company) the adhesives are not suited to the job. Both units came loose and now I'm using double sided tape. It's not that the unit is heavy by any means, just the adhesive pads are not good enough to do the job. That's a bit of a nuisance. If you are putting it on metal, than no worries. The magnets seem capable.The length of the wire could be longer if I wanted to nit-pic but I put extension wires on both units.

Light is super easy to install, dims, and color temperature can be adjusted. Nice light.

During my shop expansion project, I needed some under shelf lighting. I looked at several that were available, and settled on the ASOKO brand. I had not used these particular lights, but they seemed like exactly what I needed. I purchased 1 of the 24" variety and installed them with the small metal adhesive brackets for the magnets in the strips. I wanted to try one first to see how they work and how well they illuminate the area. It worked out very nicely.A couple things I based my purchase on were; (1) the 3 available and switchable color temps, (2) the multiple mounting options, and (3) their very narrow form-factor that made them more easily to hide. I ended up stapling a piece of door-stop molding to the front of my shelf to help a bit.After deciding to keep the light strip, I purchased 2 of the 14.5" variety, as they were the perfect length for what I needed. I installed them with the brackets and have been very happy with these LED light strips. They come with a small USB power adapter and very pliable and soft cord. Since I liked these so much, I recently purchased a 2-pack. Great value for the money.

This is exactly what I was looking for, and in fact it's better than I expected. I'm using it to light my keyboard on a rolling desk with a pull-out keyboard keyboard tray, and the light's magnets keep it fixed firmly to the metal support plate running under the desk. I hadn't remembered that metal plate was under the desk, so when I went to affix the light and it stuck to the desk straight away without the adhesive stickers, what an unexpected surprise! It also fits the space perfectly.I like the three light colors and that you can vary the intensity, and so far, it's precisely what I needed.