- Belinous Leather Steering Wheel Cover Lace Up, Stitch on Steering Wheel Wrap, Universal Fit 13-20 Inch Car Truck Pickup Boat, A Whole Piece of Cowhide, DIY w/Needle Thread (Size M4, Black)

I bought this to cover the worn out steering wheel on my 2008 Honda CRV. I previously had a “pleather” steering wheel cover from Advance Auto, and this is soooo much better! It’s genuine leather, and it looks and fits great if you follow the size chart. Tip #1: After sliding the cover over your steering wheel (with the seem in the center, at the bottom), line up all the holes with their counterpart on the other side before you begin stitching. It will look a lot neater if it’s lined up perfectly. I used a mirror to count the empty holes behind each spoke, and then marked my starting and stopping holes on both sides with a metallic Sharpie to make sure it stayed lined up well, with no wrinkles or stitching errors. Tip #2: If your steering wheel is thicker at the 10 & 2 positions, you may need to stretch the leather to avoid a gap there. Even though I ordered the correct size, based on the thicker circumference at my 10 & 2 positions, I had a gap between the leather when I got to the 10:00 position. No matter how tightly I pulled the thread, I couldn’t close the gap, so I thought it was too small. When I got to the 2:00 position, it occurred to me that maybe I could stretch the leather to fit. So I got 2 pairs of pliers and pulled both sides of the leather to stretch it a little, and then I was able to stitch it closed without a gap there. Tip #3: Rather than using “dummy” stitches in front of and behind the spokes, I tucked the leather under. As long as it’s stitched tightly on both sides of the spokes, it should stay tucked with no problem. I did tuck a small piece of double-sided tape underneath to hold it in place until I got it stitched on both sides. There are several ways you can sew the cover on. The quickest and easiest way would be the straight-stitch. I opted to cross-stitch mine, because I think it looks neater and more professional. Cross-stitching requires more time, more thread, and simultaneously using 2 needles. Therefore, I appreciated that Bellinous included 3 LONG pieces of thread, each with an attached needle, which was more than enough to get the job done. The installation took me approximately 3-1/2 hours. I’m attaching photos and a video of the finished product. I wanted to video the stitching process, but I didn’t have any way to hold the camera at those awkward angles. If Bellinous wants to send me a couple small leather samples and thread, I’d be happy to make an instructional cross-stitch video. I am very happy with the quality, fit, and final appearance of this steering wheel cover. I expect it will last a lot longer than the cheap slip-on cover I previously had, and it was actually LESS expensive! Great quality for the price!

Variation: L4 Brown Fantastic product. Great quality leather and very nice thread and needles. Conforms well to the wheel and pretty easy to install. Comes with everything you need. Can't speak on the longevity of the finish but time will tell My package came with 3 lengths of thread which was perfect for the stitch I chose. I used 2 lengths to run a saddle stitch along each perimeter prior to putting it on the wheel. Then I used the last length to make my Basting pattern and affix to the wheel. Would absolutely use this product again.

Great quality leather, well-made, and enough string for a variety of stitching options. I opted for the simple straight stitch, but instructions are available for baseball stitch or cross stitch or any others. Installation took about two hours, but I would count on three. End result is great.

The leather I received was beautiful. Soft and supple, smells nice, good thickness. The needles and thread that came with were also good. Strong waxed thread. Unfortunately, the leather tore just as I was completing stitching. It may have been my fault for pulling too hard, but honestly I don't think I pulled all that hard. I'm giving a rating of 4 stars based on the suspicion that it was my fault. 1 star off for the possibility that it wasn't my fault. Stitching it on is laborious. That's just the nature of the task. Also, there's no good way to finish the leather edges around the steering wheel spokes. Dummy stitches help dress it up, but it still doesn't look professional. I suppose you could glue it down...I haven't tried that but frankly I'd be scared to. Really, you just need to be OK with loose edges around the spokes.

Shipped fast and seems like high quality leather. It seem d a little tight getting it in the wheel, but ended up a perfect fit once it was laced up. I used the sizing guide and it was perfect. It took me almost four hours to do the job. My installation was on a lawn tractor that the squirrels had chewed on the steering wheel. It now looks like new and feels better than new. My kit contained three pieces and f waxed thread and three needles. I only used two of the threads. I did the baseball stitch. Contrary to reviews I read, I didn't break any needles. Overall I am thrilled with the quality, and the final installation.

This actually worked very well and appears to be of very good quality. They also provided two needles and more than enough thread to lace it up. The only issue is installing it and stitching it together with the included thread. Took me a while to get the hang of it and I changed my technique a couple of times before I was happy, so it ended up taking a few hours total to complete. Eventually I would put the thread through one hole on each side, compress the rim with one hand as I pulled the thread very tight with the other, then used a spring loaded clamp to keep it from loosening, like having a third hand. Repeat and repeat over and over until you’re done. Very happy with the results. It comes in several diameters and widths and colors to closely fit your steering wheel so not a one-size-fits-all approach, which would not yield good results. My car is old and the foam padding on the steering wheel was deteriorating and collapsing and beginning to rip. I first wrapped the steering wheel rim using self fusing tape to build it up and compress the original foam, which was loose and coming un-adhered in some areas. I then installed the leather cover over this tape, which worked well. I was mainly interested in function but it actually looks and feels very nice. Highly recommended, but you need time and patience to install it. If I get another one for my other car I can probably install it in an hour, but it took me at least two hours just to figure out how to do it with good results. Results are well worth the effort, feels like it’s going to last for years.

This is by far the best steering wheel cover for the money (sub $20. IMHO it would still be a good buy at $29.99). That being said, if u haven’t done this before and aren’t sewing oriented, like myself, u need to invest at minimum 1 and a half hours installing it. Took me closer to two. U should definitely do it by daytime and watch a youtube video to help u figure it out also (the printed and included instructions aren’t nearly as good as the youtube videos imho). And it wont come out perfect, like mine didnt . However, it’s still really nice and for the price a real win! Tip: pull and straighten the leather over the steering wheel as you go. In general, You will need to pull hard, like really hard to tighten the string. It’s strong, it (the string) won’t rip. U can buy a tool to pull the stitches tight, (you’ll see in YouTube install videos this tool) I didn’t have it, but in hindsight I’d recommend it. The leather seems to be high quality. It’s soft. Durable etc. I got the M4 size for my 2014 Scion XB. Took some stretching but it fit very well. It possibly can take an hour if you’ve done any kind of leatherwork/stitching before. But it’s tedious. Rewarding when it’s finished though.

Installed this Belinous leather steering wheel cover on a 2010 Kia Soul, and the result exceeded my expectations. The install process took about three hours, but once I got the hang of the stitching technique, it was smooth sailing. The kit came with everything needed, and the thread held up great—no fraying or snapping. I ended up using a custom stitch pattern because the thread was pulling through the cover a little, but once I adjusted, it came out fantastic. The fit is perfect—tight, flush, and solid all the way around. No sagging or loose areas. The leather feels premium—smooth, soft, and comfortable to grip. It doesn’t get slippery even when your hands sweat, which is a big plus during long drives or hot days. I’ve had it installed for a couple of months now, and it still looks brand new with no visible wear. The cover also enhanced the appearance of the steering wheel, making it look fresher and more refined. For the price, it’s a no-brainer—and yes, I’ve already recommended it to a few friends. ⸻ ✅ Pros: • High-quality leather feel • Tight, OEM-like fit • Customizable stitch pattern • Comfortable, non-slip grip • Great appearance and durability ❌ Minor Notes: • Learning curve with stitching, but worth it • Took a few hours, so be ready to commit some time

Installed this on my Jeep , looks great , took about 2 hours make sure you have good lighting when doing it and take your time.

Excelente funda de piel, me enviaron el producto a la medida solicitada

Se ve y se siente de buena calidad

What a great product in an age of plastic and synthetics. Allow at least 2 hours for proper installation. Looks and feels amazing.

It takes a little time to install, but it’s fairly easy. I love the great looking steering wheel cover. 100% recommended