Powered Anode Rod for Water Heater

installed this at 6pm on a Wednesday night, by 5:30am the next morning the sulfur smell was completely cone. Very easy to install although I do have a complaint that you have to buy a 1-3/16 deepwell socket which is NOT a standard size in any of my sets of impact sockets and I found it kind of ridiculous since all the other annode rods were 1-1/16 including the one on my tank. Why make everyone buy a special size???? Other than that this works extremely well so far, let's hope it is quality and lasts.

The Corro-Protec powered anode rod works exactly as it claims. It will immediately remove the "rotten_egg" smell coming from your hot water tank. Mine was pretty terrible after installing a brand new water heater 6 mos. earlier. My well water was reacting with the factory installed magnesium anode. This was causing bacteria to proliferate in the water heater and creating an obnoxious sulfur smell. Within 12 hours of swapping out the anodes the smell was completely gone. This product really works well and is worth everything I spent on it! It also has a 20yr. Warranty!! Very nice. There are some really big cons if you want to do it yourself, as I did. First problem was getting the existing anode out. It can be very challenging. It takes a special 1-1/16" 6-point socket to extract the factory installed anode. I couldn't budge it beating on my 1/2" breaker bar to loosen it. I had to finally put my 1/2" impact driver to use to get it to free up. Note: impact sockets wont fit in the anode recess. It has to be a thin wall socket. 2nd issue is extracting the anode from the tank. I did not have enough ceiling room to fully remove the factory anode. I literally had to cut it and remove as 2 pieces. I used a powered hacksaw and it took 10 minutes to do so. The last issue could be that you may need to get 110v power closer to where your tank is located. This unit has to remain plugged in to function. If you have the proper equipment needed that I mentioned above you can save a considerable amount of money in this doing yourself. My cost $185.00 Quoted price by plumber $500.00

Worked great! Easy to install. Great instructions! Really worked to get the sulphur smell out iogfvour hot water! We ordered another one for a second hot water heater!

Having that fowl sulfur smell in your water? Install this powered anode rod and you’ll see the trouble disappear immediately!! Just put one in for a customer last week. Within 24 hours the smell was gone! It really works well. Highly recommend one!

If you are looking at this product, then you have smelly hot water. Period. You've searched the internet and found lots of information, but you are unsure how much of it applies to your own situation due to the large numbers of variables involved. Plus, for whatever reason, you are reluctant to call in a professional. Yep, been there, done that, got the t-shirt. My scenario: my sister-in-law called last summer, asking for help with the water heater at her cottage. The cottage is actually a very small, two-bedroom year-round home, probably a bit over a hundred years old. And I should add that her cottage is about 75 miles away from where I live which means the entire process took awhile. The existing water heater had a slight leak. This sucker is certainly old enough to vote, might even be older. No problem. I headed to my local wholesaler and picked up a shiny new Rheem for her. Spent the better part of a day pulling out the old heater, re-working the wiring and the piping a bit and putting in the new one. Filled the heater, turned the power on, cleaned the pipe scuz out of the faucet strainers and called it good. And in retrospect here is where I made a mistake. Took the old heater to a scrapyard and got around $4.00 for it. What I should have done was removed the anode rod from the old unit. I suspect there wasn't one in there at all, but I'll never know. A few weeks later she mentioned her water smelled. Nuts. More background: I have a pole barn with one of those little point-of-service water heaters for the sink. Almost right from the start, I had smelly water out there, but since I was only using the hot water for cleaning, I ignored it. Not that it matters, but the heater is on a timer and it is only on a very few hours a week. But eventually I had enough and pulled it out. The anode rod was almost completely consumed. Ordered another from good ol' Amazon. When it arrived, I thoroughly cleaned out the inside of it with alcohol, put the new rod in and re-connected it. Within days the hot water stunk again. Since this is a family oriented site, let's just say I said "oh drat." Back to the internet. There is mention of aluminum used as an anode, but lots of cautions due to ingestion of the material. I wasn't worried about that since I only use that hot water for cleaning and not cooking. But there are no aluminum rods available for my little heater due to it being a somewhat specialized product. Being the somewhat creative guy I am, I picked up a 1/2" diameter length of aluminum rod from the hardware store, drilled and tapped it for 8-32, stuck it in the heater and ALL water problems have disappeared. Yay me. Back to the sister-in-law's cottage. I read a whole bunch of stuff regarding aluminum vs. magnesium vs. powered-anodes vs. no anode at all. I just did not feel qualified enough to make a decision for her. She wanted to stay away from the aluminum ones as she would be using the hot water for cooking. I started pricing the powered rods and we were looking at $250 to $350. I really hate spending other people's money for them if not absolutely necessary. So I suggested she call a local plumber who may have more experience with the water in her area. Did I mention this is well water? I should have. Anyway, he gave her the usual song-and-dance about how busy he was, but offered to remove the existing rod altogether. He couldn't do it, but he would send his son out. Well, this was almost a disaster. The son apparently spent 3 hours and was unable to remove the rod. No idea why. Remember I'm 75 miles away. OK, so much for that idea. She tried calling a professional and it didn't work. So now it is back to me. By this time, winter has arrived in the mitten-shaped peninsula of Michigan and the cottage was shut down for the duration. Earlier this year I did another search for the problem and this time found the Corro-Protec rod for a much more reasonable price. Asked the sister-in-law if she was willing to try it and she agreed. Ordered the kit and about a month ago went out to install it. I came loaded for bear remembering the son of the trained professional couldn't budge the existing rod. I drained the heater completely, which wasn't necessary for this job, but seems the recommendation now is to put water heaters in shallow pans. So drained and disconnected the heater and moved it out of the way. Set the pan in place, wrestled the heater into it and reconnected. Then tried extracting the existing rod. I have to explain I do have a 3/4" drive socket wrench set with a breaker bar that is a full 39" long, but no way did I need that much reefing force to bust it loose. It came right out, no problem whatsoever. I poured in 4 quarts of peroxide to disinfect the heater, then screwed the new rod in. Refilled the heater, turned it on, purged the lines and called it good. Sister-in-law called last weekend to report she was opening up the cottage and had virtually no water pressure, either hot or cold. Argh! I should have cleaned the faucet strainers. Yesterday I went over there and sure enough the strainers were clogged with pipe scuz. Cleaned them out and all is well. And finally, here is the point: after about a month of sitting there, I am relieved to tell you there are NO odors in the water. I love the product. Of course, we have no way of telling how long the product will last at this point, so stay tuned should something come up in the future. Will this product solve your particular problem? No idea. But it is a more reasonably priced alternative that might be worth exploring.

Only 4 stars for now because I don’t know about the long term protection of the tank as claimed. However, it is 100% on removing the sulfur smell that my well water had. That alone is worth the price.

Excellent instruction and easy to swap out the standard one with this one. I just installed a new water heater as my old one started leaking. After research, I found the new ones with a much longer warranty had the same components and the only real difference was the powered anode rod. For example "For a brand-new Rheem you likely want to last 15–20+ years, Corro-Protec’s 40-89 gallon standard model is the safest, most prevalent choice—strong warranty, proven results, and good support justify the extra cost for most people. It’s widely installed on similar Rheem electrics with positive outcomes." I also found "adding a powered rod will not void the warranty (powered anodes are generally compatible under U.S. law)". I thought I'd have to add a new outlet, but the power cord was plenty long enough to reach an existing outlet. installation was very easy except for removing the existing anode rod. They must have installed it with 3 people pulling on the wrench because it took way more effort than I expected to remove it. Installing the Corro-Protect rod was much easier. The fact that it extends above the top of the water heater by a few inches meant I cound use a regular adjustable wrench and not need to find a correct sized socket to install it. The green light on the power supply is a nice indicator that everything is working.

It clearly states in the ad that you will need a 1-3/16 socket to install this, no it does not come with it. I did not have any luck with local hardware stores so had to buy it online. This rod works wonders. In 24 hours my hot water went from from scrambled egg wet fart to fresh and clean smelling water. Install was super easy. Make sure you also have a 1-1/16 socket to remove old rod and maybe a torque gun to remove. Do not use torque gun to install new anode.

We spent a lot of time and money to get rid of the rotten egg smell at our new cottage. I was so mad and felt so sick everytime the water was used, I had to leave! We had replaced the anode in the new hot water tank, we attached an inline filter, we tried a filter at the kitchen tap, dropped a chlorine tablet into the tank and when that didn't work we tried pouring a bottle of hydrogen peroxide but the smell was still bad! We never thought we'd fix this until we decided on the corro anode! It just worked! No smell!!! NONE! It was easy to put in, it took away the extreme odour that came from the hot water almost immediately. We are ecstatic, over the moon! I almost never went back to the cottage until the Corro-Protec. AMAZING PRODUCT!

I tried everything under the sun to get rid of the foul rotten eggs smell in my hot water: filters with UV lamps, flushing the tank, sterilized it, increase temperature, aluminum anode, nothing worked more than a few days. Installed this product, was very easy ( you will need an impact gun with the proper socket of 1 1/16 for the original anode and 1 3/16 to install this product), but it worked, the very first day. Been enjoying smell free water for a week now and feel totally satisfied with this anode. Stop wasting your time with useless tricks from the web, if your well water has sulfur smell, install one of these on any brand new water heater and call it a day.

Muy especial y deseo que cumpla lo que tiene de garantía. Ya que es difícil que te contesten para registrar tu producto

L' an passé, à l'achat d'un chauffe-eau neuf d'une marque renommé et bien installé, les couchemares sont apparus. Senteurs d'oeufs pourris, l'anode corrodé au max, ce qui a fait dégradé les éléments chauffant à un tel point qu'ils ont cessé de fonctionner complètement, et beaucoups de rouille qui sortaient des robinets. Alors, pour remédier à tout ces problèmes, j'ai tout remplacé. J'ai fais l'achat de cette merveilleuse anode électrique, et deux bons éléments chauffant. Depuis ce temps, il n'y a plus de mauvaise senteur, n'y de rouille qui sort des robinets. Je suis vraiment satisfait de l'efficacité des ces bons produits. Je les recommande à tous.

This product is an incredible piece of engineering!! My well water is quite nasty with iron being high along with some iron bacteria also some calcium. When I used the standard sacrificial aluminum anode rod that is standard in each hot water tank to protect your heating elements, they get eaten away badly, and had to be replaced every year!! ! Every year I drained my hot water tank to flush and clean, it has been a nightmare !! The anode rode had so much buildup on it, I could barely pull it out of the tank . The worst part is the hours of time it took to remove all the accumulation of chunks of calcium and other alien looking crud in the bottom of the tank. A very tricky job with a shop vacuum and pressure washer !!! Too much to explain, but a very effective method . Albeit, a very labour intensive and time consuming job. I hated the thought of doing it each year because I knew what I was in for. NOT ANYMORE!!! Today was the “acid test” to see if this Corro-Protec electric anode rod stood up to the claims. Well did it stand up !! Nothing in that tank other than a bit of rust residue on the bottom of the tank which was easily washed away. My hot water tank job took me less than an hour after the water had drained out compared to the regular 5-6 hours before!!! This corro-Protec is nothing short of amazing from my experience. If you go through the same BS I do with tough well water, you definitely will not regret buying this product. I’d give the product 10 stars if I could.