PVC Termination Cap Mesh Screen Vent Cover, Furnace & Roof Vent Cap, Stainless Steel Wire Round Exhaust Pipe Cover End 2" Inner & 2-3/8" Outer Diameter

I think these will work very well. They are well made. The mesh is strong and secured solidly to the PVC. I ordered the wrong size. I ordered one size larger than I should have. As luck would have it, it fits on the outside of my vent cover rather than the inside. That suits me just fine. I'm going to find a pin to secure it and drill a hole through the 2 pieces, as an extra measure. That way I can easily remove it if need be.

Perfect Fit for the 2" venting installed w/our new furnace. The ends are a bit wider at the end (bell opening) so these caps fit perfectly inside the end of the PVC. Effectively blocks bugs and other small annoyances from entering the exhaust venting. I would order again and recommend should my use case fit your circumstance. Good Product vs Price> A-

Fits perfectly. Exactly what I needed to keep birds out of my PVC pipe. Seems like it is a quality product which will last.

Fits inside my 2" SCH 40 PVC furnace intake and exhaust pipe. Keeps the bats out.

Nice and solidly made. Tight fit on the inside of the ayre vent, with no worries about it falling off.

Worked perfectly to seal off my furnace intake and exhaust pipes exiting my house. Had a mouse crawl in my furnace air intake last year and die in the blower, so this should prevent that disgusting outcome from happening again. Easy installation and good price.

I am using NDS sewer & drain 4" PVC pipe for ERV ducting. This is not SCH40 pipe but thinner wall sewer & drain pipe and fittings. This 4" screen fits inside an NDS hub by using a heat gun to soften the hub. It is not easy and it took me about an hour to achieve but it has worked out very neatly in the end, see photo. Once the hub is very warm / too hot to touch, I forced the screen (which has a solid pvc collar) into the hub perpendicularly to expand the hub while rotating it to expand the hub evenly all around. Repeating the heat and expand procedure many times eventually allows the screen into the hub. Once it is slightly inside evenly all around, it is much easier to continue heating and press it in all the way. This long turn elbow will be pointing downwards on the fresh air intake. I will not glue the elbow to the pipe so that the elbow can be easily removed for cleaning. I can reach the inside side of the screen through the removed elbow. Therefore it's fine that the screen is now stuck permanently in the hub just through friction with the warmed pvc. I have bought several of these screens in the past for air intakes and very happy with their quality and longevity. I point them down on air intakes where I can easily see and vacuum them every now and again. No screen on exhaust provided exhaust is in regular daily use to expel the bugs. In my case the ERV will be on 24x7. If PVC is in direct sunlight it needs to be painted to protect from UV. I don't know if the 3" size fits inside a 3" NDS hub but it's worth a shot.

Exactly what I needed to keep bugs out of a furnace air intake without impeding air flow. This PVC "termination" vent is the exact same size as a 3" PVC pipe, so that means it needs to be fitted into a 3" coupling. It fits in the coupling tight and exact, so once it's in place, no need for cement or caulk. The only drawback with the couplers I found at the local big box is they're fairly long, making the vent protrude further than it used to. I'd love to see a version of this screen that was sized like a coupler so I could just slide it over the end of the PVC pipe without an additional piece. That would probably be a non-standard way of doing things, I realize, but these sorts of exhausts are often pretty random designs anyway. The old design (that I replaced) had slats to keep out birds, but did little to keep out bugs, and was looking rough after 20 years outside. I'm pleased to have a nicer looking, more effective screen over my furnace intake. Recommended.

Worked fine. Used to replace a cowl end that was very restrictive on the roof. Used a rubber coupler found at bunnings hardware in Australia to attach.

Fit fine.

great product

Perfect fit to keep the critters out!

Perfect fit!