1/8" 22t Coaster Brake Cog | Chrome Steel 22T Dished Cog for Sturmey Archer 3-Speed Hubs

I've been on a bit of a Raleigh 3 speed (or more like a Sturmey Archer AW hub) kick lately. I have had one for decades but rarely rode it, as it seemed it was geared too high, but I had other bikes and never thought of it. That one had a 17T cog on it. I more recently researched the issue and found how simple it is to change gear ratios. After buying my first 22T cog, now I love the bike. It will go up moderate hills with ease and still go fast enough to get somewhere at a decent pace, they all should have shipped with this setup. If you want to stop there with the review, that's fine. Otherwise, read on. So of course I went and bought more bikes. Two that I bought recently had 18T cogs and a third, a 20T. All run 46T chainrings. Researching deeper, the 18T cog is the typical standard. In gear inches , 46/18 gives you the following spread: 50, 66, 89 Perfectly fine for flat areas like most beach communities, but if you have ANY hills at all, you're going to struggle a bit. With the 17T, it's worse with a 53 gear inch low gear. That's about the same as a typical BMX bike is set to, for a comparison. Well, with the 22T cog, what was your easiest gear basically becomes the middle. Gives you a climbing option and still a "go faster" one too. 41, 54, 72. I believe this is the largest cog that Sturmey Archer makes. There's a 23T Shimano Nexus cog that will also fit these hubs, which would give you 39, 52, 69. Loses some top end speed and makes you want to be in high gear much more than with the 22T. But, it too is great with the hills. It's also good for a youngster with a little less leg strengh. The original 3 speed Raleigh Sports I've had forever now has the 22T on it, my wife's Raleigh Sports also has a 22T on it, my son's Raleigh Colt has the Nexus 23T on it and the 4th Raleigh that is currently running (and for sale) is a Sports with a 20T on it. If I decide to keep that one, I'll probably grab another 22T, or bring it to the beach and not have to worry about hills. I will also note, with the Sturmey Archer 3 speed (and probably all IGH setups), the lowest possible cog you should ever run would be one with half the teeth of your chainring. Do not go with a larger cog than 23T with a 46T chainring, or 22T with a 44, 20 with a 40, etc. The torque created on the hub is too much for it to take. So, if you try to solve the "this thing is too hard to pedal" issue at the chainring instead, be mindful of that. If you've gotten this far, thanks for reading my deep dive into Sturmey Archer AW 3 speed gear options.

This makes my 66 Rollfast Royal a lot more practical as a commuter

Makes beach bike riding easier on knees for long rides. I love A single speed. I'm all about exercise and health

Great Sturmey sprockets, this one is being used on a mid 80's Murray coaster-brake single-speed with a simple circlip lock-ring. Very happy with this component 👍

This is an easy upgrade you can do yourself which significantly improves the rideability of a a bike with a smaller cog.

i have a huffy 'Cape Cod' beach cruiser. its a tank of a bike. the 19tooth rear cog was just geared to high for weight. this 22tooth cog did the trick to make it a nice 'poke around at swapmeet' bike. you may have to lenghten chain depending on your gearing change. swap out was an easy pop off slip ring with screw driver, and pop on. cog was in chrome

This cog is great for lighter gearing on your bicycle. you will need to add links to your chain. cog is easy to install.

My son's cruiser bike has a 1967 Sturmey Archer (SA) 5speed hub. I needed to gear it down a bit to deal with the Colorado hills. The original rear cog is an 18t, and the 22t makes a huge difference. I needed a cog with offset to keep the chainline correct, and the SA cog fit the bill. Just a note about compatibility. This is a standard 3 spline single speed cog. It is the same spline pattern that was later adopted for coaster brakes by Suntour, Shimano, Bendix, and many others. It is also used on quite a few geared hubs fron Shimano, andn Sturmey Archer. So, any 3 spline cog will work if you are looking for a cog that fits your 3 spline hub. It just happened that the SA cog was the least expensive at the moment.