140*200mm FEP Film

Although this was my first time trying to replace FEP, I didn't have any problems because it was smooth, wrinkle-free, and the size was right and it was placed perfectly. The print came out perfect. I'm very satisfied with this product.

Fits perfect on the anycubic photon mono x

There is a short video on how to replace these for my printer (AnyCubic Photon). A lot of screws but in the end it was very simple and took no more than 5 minutes. Clean everything off first and make sure you have a bottle cap from a soda or water, place it under the film as you're replacing it to create the tension on the first set of screws. Remove it when re-attaching to the VAT and it goes on nice and tight. Use a razor or x-acto knife around the inside edge to easily remove the excess and you're good to go. I tested a print almost immediately after that was an issue, I just re-zeroed the printer since it was slightly off and voila, back to perfect prints!

So after some mixed information I took a chance and yes this indeed does work for the Anycubic Photon Mono printer. It's a little big for the vat but requires very little trimming. I installed it then took an X-Acto knife and cut it along the bottom edge as needed. It also last for a good amount of prints. I could get about 40-50 prints out of one sheet before seeing some slippage or fails so yeah, highly recommend this film for printing.

Used for an older Photon S model and worked perfectly, only real gripe would be it picks up dust really easily and doesn't outline removing the film from the sheet prior to installation. Came perfect without scuffs and scrapes which can't be said about most FEP sheets on here. Definitely the best FEP sheets I've used in some time, has all the normal problems (scuffs easily), but with practice you'll get used to clean and safe installation. No stretching necessary, fits perfectly with some wiggle room, highly recommend!

It wasn't until after trying this product that I discovered the FEP film assembly that comes with the Anycubic Photon Mono 4k printer cannot be repaired by just replacing the film. The instructions show assembling the film with 2 steel frame pieces. However, the assembly that comes with this printer has 2 plastic frame pieces that hold the FEP film. I tried separating the 2 pieces to add this film, but the pieces would not fit over the film properly as they are not designed to be taken apart. Unfortunately I ended up having to buy the assembly that has the FEP film already installed with the plastic frame pieces. As it turns out, Anycubic changed the design of the resin vat that ships with the photon mono 4k. However, the seller worked with me and refunded my purchase after we realized this change was made.

Great customer support! Helped me with my issues promptly! Quality films and quick service!

Bought this as my first FEP replacement to my Anycubic Photon 4k. Prints started consistently failing so I figured it was time to change it. Now my prints are coming out perfect. And I totally didn't forget to take off the protective film of the FEP before installing it. So don't do that thing I didn't do...

I bought these instead of my usual branded ones for my Anycubic Photon. I thought it might be a bit of a risk as they were half of the price, but had to save money so thought I’d chance it. I’m really glad I did. Side by side with the last of my other ones I couldn’t tell the difference, and it’s performing fine after about 10 prints now. It actually seems to hold up a little better than the Anycubic ones as it’s barely tarnished. The only thing it could do better is the packaging. They were in a standard envelope within a padded envelope. This means no protection against bending. It would be better in a card sleeve

Je l'emploi pour mon imprimante 3d elegoo. Rien à dire quand même assez epais.

El secreto está en tensarlo lo mejor posible, ahora bien es un robo que un trozo de plástico cueste tanto, y eso que este es de los mejores.

I bought last film from seller and of course package arrived broken 💔 but after unpacking and installing all seems to work. Next time please put it also in bubble wrap otherwise if that is not handled with care product is useless....

Fyller sin funktion till 100%!