PBYMT 1157 Front Rear LED Turn Signals 1156 Bullet Turn Light Indicator 2 Inch Smoke Lens Cover Compatible for Harley Dyna Softail Touring Street Glide Road King 1986-2024

I installed these LED turn signal replacements on my 2022 Street Glide. The included instructions were clear and in reasonably plain English - extra points for that!Important points to remember:1. When removing the rear turn signal bulbs, carefully note the positions of the lugs on the bulb base so that you can align the connectors the same way.2. If your rear turn signal bulbs have 2 contacts, use the 2 contact connector bases included with the kit. 3. Keep a careful eye on the foam tape pads in the kit - they WILL fall into the least accessible space on your bike... ask me how I know!4. When installing the connectors into the bike's turn signal sockets, you will have to press them in quite a ways before being able to turn them. I was able to do it with fingers but you might have to use pliers if your fingers won't fit. Be careful if you do use pliers not to damage the connectors!5. Pay attention to the placement of the screwdriver slots on the included lenses when you install them so that you can get to them if you need to in the future.I plugged in and tested all 4 lights before completing installation due to feedback here regarding LEDs that didn't function. All 4 sets I received worked perfectly. Then I attached the included foam rings on the front of each LED cluster but did not peel the protective layer from the side of the foam ring away from the LED cluster. That way the foam ring won't stick to the smoked lenses in case I have to remove them in future.Once installed, the LEDs are much brighter than the OEM incandescent turn signals. The front white ring running lights/center yellow turn signals worked perfectly. I did not have to let the hazard lights run to correct hyperflash, the lights operated correctly as installed. I'm happy with them but time will tell if they fail. Still a bargain at this price.

***UPDATE*** customer service reached out to me on their own and issued me a full refund with the evidence provided. As i put in my initial review this product looks and works great, other than the one light that was defective. Looks better than Harley, the price point AND the customer service, this is a win win…..changed my rating to 5 stars bc , what else can you ask for….The nipples on the tip that lock the lights when you turn them were misplaced on one of the front lights. all the others worked great and looked great. i could have returned but really didn’t need the back lights so i just cut one of the back lights and soldered the end on. This is not ideal because i wasted money. i guess you take chances when you buy cheap knockoffs. other than that the lights look great.

I bought the four bulb set really just to get the rear lights and lens set. Installation only took a couple of minutes. I opted to use the rear stock red lenses just because they are a little bit brighter then when used with the smoke lenses. Bright and high visibility is what I was going for, although the smoke lenses are very nice looking on the bike! Without syncing canbus the turn signal indicators will blink faster then the turn signals. This condition can be easily corrected using the following procedure:2014 and later.Turn the Ignition on, but do not start the bikeTurn on your 4 way hazards by pressing the hazard button on the controlsTurn the Ignition off letting hazards run. If the bike has security they will flash 5 or 6 times and then pause. This is expected. They will go back to flashing normal hazard modeLet hazards run 1-2 minutesTurn the ignition back onTurn the ignition off and then back onCheck the function of both turn signalsThese are an economical option to some of the more better know led's out there and I believe a good option. Id love to run the more expensive options out there, but these are a fraction of the cost and do a good job. Time will tell more about longevity and quality.

Pay attention to how the tips on the bulbs are oriented when you take out the originals, they are not directly across from each other, and you'll be fine.Complete plug-and-play on the 2014 Dyna Wide Glide.Looks great with the smoked covers but rears seem slightly dimmer than stock. 1000% improvement of visibility on front running lights and turn signal. I especially like the halo light look.Took off one star for brightness, but only about the rear.Time will tell on the durability...

The media could not be loaded. These fit my 2012 Road Glide perfectly! The install might have taken me 5 minutes .... Maybe. The instructions were fairly clear (Ikea picture style) but discernable easily.They look great are bright, and fit perfect.I will update if there are any issues, but right now I'm very happy. If you're considering these, I'd say go for it!

The media could not be loaded. Even with the smoked lenses I put on they are very bright and look super sharp.One thing I feel compelled to mention is they are NOT plug and play for the front blinkers. The back was fine as it had option to swap the connector between 2 or 3 wire options. The front ONLY had 3 wire option. For my 2000 HD Road King that meant I had to rip out the OEM socket and wire it up manually. And then further had to add a wire to tap power off the side lamps if I wanted the outer halo ring to light. This was not difficult by any means but unexpected nonetheless. That's how it goes with antique bikes sometimes, adding new upgrades is rarely simple or easy. Still, I am happy with the lights. They look great and good value for the price.