KEMIMOTO Fender Eliminator Compatible with Ninja 650 2026 2025 2024 2023 | License Plate Bracket Tail Tidy Compatible with Z650 ZX650 2021 2022 2023 2024 2025 2026 Ninja 650 Accessories

2021 Ninja 650 from the factory looks aggressive until you get to the back and see that elephant trunk sticking out! Lol Now the bike looks like it should have from the factory to begin with! Awesome product. Watched a YouTube video how to install it. Took 40 min to install. I'm very hands on and have electric tools but had no clue how to do this without following steps first. Take your time removing the pieces off the bike and make sure you position then into place. This piece fit like OEM! 👍🏼

Looks great on my husband’s 2025 Ninja 650—perfect fit. Just watch a couple install videos and label the indicator wires to keep it easy.

Easy to install and simple

This item fits perfect and greatly improves the clean up of the tail piece. The original is ugly and too big. There are no instructions included, but go on line and you will see how to install. Takes about 45 minutes taking your time. Very solid and good quality. Great price point.

Good durable finish, simple design. Aluminum is a good gauge, sturdy great fit with the OEM parts for a changeover.

This bracket brought better looks to my bike for not much cash. Getting rid of that long plastic tail made my bike look sleeker and even a bit smaller. I like the minimalist styling on my naked bike, and was glad to see I could get this mod done so cheaply. As someone in metal stamping, I can say the construction is solid for what it's made to do. Installation is very straight forward, with the hardest part being squeezing the factory mounting grommets in, followed by removing the stock tail. There's a screw holding the stock one on even after you remove the bolts. It's under the frame bracket, so you either put a screwdriver through a hole and bend the under cover down until you can get it, or you can go under it with a low profile driver. I used a bit in a ratchet. Take the brake light off to let that cover down. Other than that, it's just shove in the lights, fish the wires, and tighten the nuts on the studs. My only negative is that it was slightly too big in the corners to fit the indentation in my 2019 Z650. It's just a bit too sharp in the corners and hangs up on the larger rounds in the plastic on the bike. I went for it at first, but the tightening felt too progressive, and I redid it before I dug in. A few washers stacked around each stud for spacing and it tightened up quickly (as a solid stack should). Still looks great. I might have also designed it myself with headed clinch studs for holding power. Nothing broke, but I couldn't help thinking the flush stud might pull out if I happened to overtighten. Likely not an issue if you don't overtighten.

Perfect fit and excellent!!!!!

This plate holder looks great. Very easy to install. You do need to understand how the side signals are squished fit into place. Just look at them when you take them off the original stem. Don't forget to put the plastic piece back in the inside. That's why that other guy's signal fell off. This fit my 2024 Kawasaki Ninja 650 perfectly. The original wires are a bit of a pain, but not difficult. You don' have to take off all of the panels like several others mentioned. There is one screw that is screwed into the plastic only underneath. You can just pop this out by pulling on it. You don't need to take the whole tail apart. But it's up to you. If that freaks you out, then take the tail apart. Both ways work fine.

Material muito bom, encaixou certinho e fácil instalação. Sem necessidade de fazer adaptações.

I hate how ugly the stock license plate fender looked on my Ninja 650, so I decided to finally do something about it. Installing this new fender itself was very easy and straightforward. However, the process of dismantling the rear of the bike, disconnecting the lights, and removing all the parts to actually ACCESS where you need to work, was incredibly frustrating. Especially for someone like me who has never tried this before. I highly recommend following a YouTube video on how to take everything off. You’ll need multiple allen keys and ratchet tools of different sizes. Also, the very last Phillips screw at the bottom of the stock Ninja 650 fender is annoyingly hard to reach. You’ll need a long skinny Phillips/flat head screwdriver to reach it. Thankfully, the Kemimoto fender eliminates the need for that final screw. This kit includes bonus screws, but you won’t need most of them. You can reuse the screws that came from the original fender. As you can see in the picture, the Kemimoto fender eliminator looks amazing once installed, tidying up the back of your bike. For reference, I am riding a 2023 Kawasaki Ninja 650, and the license plate sits snugly underneath the taillight.

past pefect op kawasaki Z 650 2024

Bit of a more in depth install due to having to find your signal and plate light connectors but pretty straightforward and easy to install. Cleans up the back of the bike and looks great