YOSUN v13h010l49 Projector lamp for Epson elplp49 powerLite Home Cinema 8350 ...

Less than 400h and the light become dimmed. Still Works ok . UPDATE: Now after 5months of extensively used (~ 5 hours each day ) it is Still works without further degradation.

Six months after purchase it died, don't waste your money, for close to $100 i could have bought the original and it would last me a few years.

I gave 4 star becouse not like the original lamps.Pacaging very good careful deleverd on time.

The lamp is very easy to replace, and since I have a new replacement lamp, my projector has performed well. I would recommend this company to anyone who needs projector parts. The service is also great. Thanks.. to get my projector back to work.

I'd rather buy a replacement bulb for my Epson video projector in the future,cause it is really much valuable that I purchase an OEM one. It will cost me as three times as the same functional item. This replacement bulb was a manufactured bulb from YOSUN,currently I found no defectives on this bulb. It was perfectly matching the machine. The brightness was even much better than my original one. Pictures were clear enough as the images showed that.

JUNK! go buy the actual light from the website and do not waste money on this crap. Was out in less than a month. What a waste of money. So frustrating.

Typically I I buy ~$35 bulbs and have to re-seat them in their housings before install to get them to perform properly, and they last about 1000 hours or so before they get noticeably dimmer and I start thinking of replacing them...and then finally break down and actually do it at around the 1500 hour mark when it becomes unwatchable in all but a totally dark room. I decided to spend the extra money on this one in the hopes of not having to work on it before the install, and having good brightness a little longer between bulbs. I was pleasantly surprised that it was properly seated in its housing and looked like a decent bulb, although none of these aftermarket bulbs really stand out from each other when holding them in your hands. I installed it and immediately noticed that the bulb was no brighter than the bulb that I was replacing. I figured I would give it a few hours to break in and possibly get brighter. ...It didn't. Ultimately the color isn't very good, and has a slight green cast to it. This bulb also flickers noticeably at times, and then will steady for an hour or so before flickering for a while. Nothing major, but enough to give you a headache for some unknown reason, like listening to a radio station that's just a little out of tune. You don't realize how bad it was until you turn it off and everything gets better.

Well, this bulb is a clone of the OEM bulb. It installs and fits the same. It does not come with instructions for the install the way the oem bulb does, but those are in the manual for your projector most likely (they were for mine). I am disappointed with the brightness. This is my third bulb overall. Last time, I put in a new OEM replacement which cost twice as much. When new, that bulb on my project's brightest mode was so bright it hurt my eyes. This was also the case when the projector was brand new. But this bulb is significantly dimmer. I dont know if perhaps it is defective. There are no noises or smells, and the picture is otherwise fine. But like in a dark room, the picture is practically unwatchable in theater mode which I used all the time previously with OEM bulbs. I will contact the seller to see about a replacement. Just not good enough.

Il n'est plus possible d'acheter la lampe sous la marque constructeur. Et, il n'est pas possible de savoir sir la lampe bénéficie de la technologie de miroir lui permettant de produire plus de lumière. En fonction de ça, mon avis ne sera que subjectif par rapport à cette lampe. Elle est de meilleur qualité que les deux précédentes lampes que j'avais mis dans le vidéoprojecteur (j'avais des variations d’intensité de lumière lors de la projection de scènes claires). La lampe projette une lumière qui est stable, je pense avoir retrouvé les sensations que j'avais lors de la réception de l'appareil. Pour l'instant je la considère comme un bon achat pour le prix, à voir si cela se vérifie dans le temps.

El modelo embona perfecto para el proyector Epson Home Cinema 2030, simplemente quité la lámpara original e instalé ésta (V13h010L78). 3 meses de uso (90 horas) sin problemas, remplacé la lámpara original con ésta después de 5 años y el proyector recuperó su brillo. Para prolongar la vida de la lámpara recomiendo darle uso en brillo “normal” y una vez que cruce las 100 horas cambiar a modo “eco”, así como evitar encender y apagar el proyector por periodos cortos, lo recomendable es mantener la lámpara en uso por periodos de por lo menos 2 horas antes de apagarla.

No se ve mal, pero hay una diferencia muy notable respecto a la original además se escucha un pitido prácticamente continuo, sobretodo si el proyector lo tienes en el techo sobre la cabeza.

Encantado, muchos más económica que la original y ni se nota, nada más que en el precio.

Very prompt deliverance.