Keyless Entry Remote Replacement Key Fob Fit for Toyota Rav4 2006-2010/Scion XB 2008-2013 Vehicles that Use HYQ12BBY with 4D67 Chip (2 Pack)

So to be completely transparent, I never actually cut these keys. I bought them only for their keyless entry ability. The keys were very easy to program, and worked with my car flawlessly. The fact that these keys are so cheap, when the original are hundreds of dollars make these a must have. As far as durability goes, that is a hard one. The original key snapped, and Toyota told me that these kind of keys, even the ones that cost hundreds of dollars, snap easily because they are plastic inside. Well, if that is the cause, why not just buy this and replace it when needed?

My old key fob died and the buttons did not work. This was a perfect replacement for my car, a 2008 RAV4 Limited. As stated by other commenters, finding someone who is willing to cut your key is the hard part. I also had a hard time finding reputable sources on registering the key to the immobilizer and programming for my car, so I ended up having a local company do mobile service and had them cut and program the key for me. Overall, I'd recommend following this process if you want to avoid paying boatloads of cash to your car dealership.

These were exactly what we needed for our 2008 Scion xB. While we had plenty of spare keys, we never had an OEM unit and had grown used to manually locking and unlocking the doors. After cutting, the keys fit the doors and ignition perfectly, and programming the fobs took about 30 minutes. Now, we enjoy the convenience of remote locking and unlocking, along with the added ability to activate the panic alarm when needed. This option saved us over $200 and the hassle of spending hours at the dealership, not to mention avoiding the inconvenience of being without transportation. The buttons can be a bit sluggish at times, but overall, it’s a fantastic value. Highly recommended if you’re looking to create spares for your Scion!

Since my local hardware store was not willing to cut a blank key that was not their key, I decided to put the new internal part from the Amazon remote into my old remote. Now I have the original key with new parts. I got the instructions from the recommended www sites and printed the instructions. I tried several times but it did not work. I went on You Tube and found a video which showed that I was going to slow. There are timed requirements (within 5 seconds put the key in and out two times). I got the pace down and tried again and it worked great for two original remotes. I decided to put the old parts into the new Amazon remote. I programmed it using the working remote with the original key. I used the new blank key when I could and the cut key when I have to turn the key to the on position. I used the new uncut remote for the last two steps. It worked perfect. I am hoping to talk Home Depot into cutting this remote so I have a spare. Another alternative (without cutting the new key) is to program the new Amazon remote using your original key and just use the Amazon key to remotely open the car door. Why I I happy? I have three remotes that work the car’s locks for under $30 instead of paying Toyoda upwards $400 each for a new remote. Now that I have this knowledge, I would recommend that you replace the battery and reprogram the old remote to be sure that doing this alone will not solve your problem first. Either way I am very happy with the results.

I bought these for a few bucks and programmed them myself off of a YouTube video. Toyota wanted 500.00 dollars to program and cut just one...total scam. I'm taking them to a locksmith and getting them cut for about 50.00

Programming instructions were incorrect but you can find instructional videos online. You must cut blank key before it can be programmed at home. Blades fit into door locks & ignition perfectly. Came with 2 keys. Was only able to program one of the two . Still cheaper than dealership but quality is identical to OEM.

Went to get these cut today, first had an off the shelf blank cut to verify match, worked perfectly, started the car and drove home with it. Had one of these keys cut right after and it only cut one side, and cut it DEEP (see picture). The other side was barely touched. I did a close exam and found the reason is that the center groove is too wide, and the raised portion is slightly small than the OEM key so when the key was run through it appears it pushed the key too far to one side causing it to be miscut. I didn't try the second key after seeing what happened and will look for a place that has a manual key cutter so it can be properly aligned. In the meantime will look for an empty shell blank and hope that it has the correct sized grooves. On thing I also noticed is that it is difficult to insert into the lock.

I tried and tried to program the fob per the sites i had received in the package. One of the fobs failed over & over. But the second pair after some trials worked. However, for some reason to remotely open all doors ( not just the driver's door) its a challenge even when i double click to unlock. Note: i have had tmy remote fobs from the manufactory for many years, so it's not like i am knew. After i programmed it, i took the fob with the key to my toyota dealer to cut (create) the key for my car. They charged me only $10. Had they had to program it they would have charged it $200. Then if i had bought the fob from the dealer, it would have cost $250. So i came ahead, only if both fobs would have worked & i didnt spend too much time for programming it.

I use it for my Toyota they are perfect very satisfied

Vienen para programar y cortar ya que lo haga alguien especializado pero el chip de excelente calidad, cada una me salía en 1800 y pague 600 por el corte y programación

Works great. Can’t believe Toyota tries to charge $500 for the same thing

La llave funcionó perfecto para abrir y cerrar los seguros de las puertas a control remoto siguiendo las indicaciones de la liga qué te dan. Solo me falta llevarla con el cerrajero para que hagan la copia y programen el encendido del motor.

Original FOB electronics were fine & were able to move these from the old to the new key blank FOBs with no problems. Getting a new key cut using the old key as the template also no problem. However programming the new key does require a locksmith or someone with this know how as it is a methodical series of steps. Since we needed two new keys it was worth going this route and cost.