Universal Garage Door Remote Universal Gate Opener Remote Cloning Homelink Programmable Learning 4-Buttons Multi Frequency 280MHZ-868MHZ 2019 Upgraded New Version

I am very satisfied with this purchase. I recently bought a condo and I have a detached garage. They gave me a big old chunky garage clicker, which I have to carry around with me every single time I leave the house in order to open up the garage and get to my car (or otherwise insert the actual key and struggle to make it pull up manually which is a hassle). Get all my belongings, and then grabbing up my big old clunky garage door remote, and heading out the door was a super duper hassle. Plus the button on the chunky remote would click at the faintest touch, so I was constantly worrying if I had clicked it on my way back after getting home and leaving the garage door open all night..... Anyway, this thing is a life saver. I received it today and so far am EXTREMELY happy with it. I will update this review in the event that any problems do begin to occur. (1) Design This thing is actually quite stylish. It is thin and small and has a very nice "soft" touch to it that makes it feel high quality. There are four buttons. Pushing them is easy but not so sensitive that the faintest jolt in your pocket will activate them (in other words, if you want to open the garage, you'll need to intentionally push the button; it won't open by mistake just because you have it in your pocket). Also, and this is a big one because it was something I was looking for before I bought and couldn't tell if this had - this does work to put onto a key chain. It has a space on the bottom where a string slips through (included in the box) and then the string attaches to a little hook that you can attach to a key chain. Very nice and convenient. (2) Performance So far very good performance. I have tested it from about thirty feet away from garage (with both the door open and closed and within a vehicle) and it receives the signal flawlessly. (3) Set-Up Set up was easy enough. Hold the number one button down while pushing the number two button four times. The remote starts to blink. Press the button of your original garage clicker to transfer signal. Then push whichever button (1,2,3 or 4) on this clicker to assign the signal to a button. Takes about 30 seconds. ** For mine, after I completed the above step, I then needed to "authorize" the clicker with my garage door opener. Inside your garage on the back of the box, there should be a "Learn" button. I brought this clicker in there, pushed the learn button, then pressed the assigned button on my remote, and this device was instantly accepted and began working.

Perfect if your car doesn't have a garage door opener/HomeLink capabilities. It's also good to keep on you as a spare in case you lose the original opener. Very easy to set up and can be used immediately. I'm able to use it from approx. 50-60 feet away from my garage, and it works perfectly. Only issue I have is the replacing of the battery. Once the original battery wears out and you need to replace it, you have to take the backing off to replace the battery, then snap it back on. After snapping it back on, it is not going to be as tight as it previously was, causing connectivity issues with the battery and circut board. But for the price, I'm perfectly fine with overlooking it!

I thought I would try this based on promising online reviews. It is simple to program, and it learned my LiftMaster garage door openers seamlessly. I challenged it with a Ghost Controls gate opener and it appeared to learn the code, but it did not open the gate. I can't say I am surprised though. From the Ghost Controls website: Non-Ghost Controls Remotes Different Brand Remotes Can I use a Remote Transmitter from another Gate Opener manufacturer to control my Ghost Controls system? No. Only Ghost Controls remote transmitters and keypads will be able to control a Ghost Controls Automatic Gate Opener System. We use a proprietary algorithm that we call GhostCode to control our system on 433.92MHz. We designed our systems this way to maximize the long range operation of your radio frequency (RF) devices so that you can open/close your gate from further away. If you instead want to add the convenience and versatility of Ghost Controls to your existing system, we encourage you to look at ourAXUR Universal Receiver Kit that would allow you to use a Ghost Controls remote and keypad with another manufacturer's access control system.

This is a very good little garage opener. While other garage openers require you to open the control box on the garage door mechanism and hit the "learn" button, this one can directly duplicate a signal from your existing remote in most cases. It worked for me anyway and was pretty easy to set up. A different XIHADA remote I had failed after about 5 years. I think part of the issue is the buttons broke. This one has more satisfying "clicky" buttons, while the other had just a little rubber bulge that you had to squeeze and often we had to squeeze very hard to make it work so that probably shortened its life. I hope these clickier buttons will be more durable but only time will tell. Remote itself has a soft, rubber-like texture. Nice to hold. Sometimes I find this type of texture becomes gummy and awful after several years, but that didn't happen to the old one so hopefully not this one either. Cost is OK although I think a little bit on the high side.

Doesn't work with most mainstream overhead garage door openers

Programmed successfully to a Nice brand gate opener and Genie Intellicode garage. For Nice gate, included instructions worked. For Genie Intellicode, throw out the included instructions and follow these steps: 1) Press LEARN on your opener overhead unit. The unit’s light will blink. 2) Place your cloning remote into clone mode (hold button #1 while pressing #2 four times). Your clone will blink slowly. 3) Hold down original remote button while close to cloning remote. 4) Cloning remote should eventually light up solid, followed by fast blinking. At this point press whichever button you want to program for the cloning remote. Now you can also release the original remote button. 5) Your overhead unit’s LEARN light should now be solid. Press your ORIGINAL remote once to remove the solid light. 6) Press overhead LEARN again (blinking light), press your cloning remote selected button (solid light), press it once more to remove solid light. 7) Grab yourself a beer to celebrate, it now works. Good luck

My daughters family live in a gated community and we spent the month of December with them. I ordered this because it was much more convenient to use for getting the large entry gate open (otherwise we needed to punch in a code and we have had issues with that over the years). It works well and is a good value, but I am downrating it because it was very difficult to program. My son-in-law programmed it for me, and he is a techie kind of guy who is good at that kind of stuff, and he struggled to get it programmed.

These are quite small and worked great on my older Liftmaster with yellow buttons. However, in.my new house with yellow button MY Q enabled Liftmaster opener, they did not work at all. The web site clearly stated that some newer MY Q enabled units will not work with this remote. So 5 stars for excellent performance with the right unit and 5 stars for clearly stating that they won’t work with specified models. Highly recommended for older units, even older MY Q ones.